KUIX505ESS0 KitchenAid Ice Maker - Instructions

Took knife and pried out the the damaged switch. Took wires off. Put the wires on the new switch and put it back in the hole. Job finished. The part shipment was very prompt and I am happy. The End!

Pried out old Switch,Hooked wires to new switch Snapped in New Unit.
5 minutes Total Time

plugged the two wires in and snapped the switch into it's socket.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

shook bottle and painted waited a day and repeated

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

My husband watched the video on the repair and followed it step by step...works like a charm! The repair shop wanted 299.55 to fix it - the part was 79.00....big savings by doing it ourselves.

Unplugged the refridgerator and pulled the rear cover. Had to take the fan blade off in order to get at the screws holding the existing motor in place. Removed the old fan. Pressing the new plastic fan onto the new motor shaft was a little more effort than expected, but I guess it won't come off. I have large hands so mounting the new unit was a little bit of a challenge getting the small screws started. Once the three screws were tightened all I had to do is plug the electrical connector in and replace the rear cover. I was happy that the existing electrical connector was the right one for the new motor too, and that I didn't have to use the provided wire harness. All in all the repair went pretty well.

I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.

The repair went just fine. Your instruction regarding using the wiring harness were clear. Most of all I am happy to not have to listen to a noisy motor all night.

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

as told per compter