KUIC18NNZS0 KitchenAid Ice Maker - Instructions

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Instructions were really clear and easy to follow. Hardest part of the job was moving the refrigerator away from wall after it was filled with holiday groceries.

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

I surfed partselect and read that a reader had a similar problem with a rattling fan. I then removed the back panel, after I had unplugged the unit, and was able to feel the slop in the fan shaft. I then watched the video of how to replace the fan and ordered the part soon after. The part arrived 3 days later! Easy to do. I was finished in 12 minutes and the fridge runs silently. The part of the job that took the longest was vaccuming the undercarriage. There was alot of dust! Couldn't have helped the efficiency on the fridge. Keep it clean.

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!

Pulled out old switch with needle nose pliers, unplugged old switch and plugged in the new one and snapped back into place. Very easy to repair. Took less than 10 minutes

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

My husband watched the video on the repair and followed it step by step...works like a charm! The repair shop wanted 299.55 to fix it - the part was 79.00....big savings by doing it ourselves.