KIMF81 KitchenAid Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Boring, OR
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
motor assembly was shorting out
I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.
Paul First time dealing with you ,thanks
Paul First time dealing with you ,thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marinus from Crestone, CO
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker stopped working
Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ACWORTH, GA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
was NOT making ice
Your youtube ..order part and fix in 2 mins.AWESOME we had our refrigerator since 1983.... my wife keeps her looking new...& happy with the saving .Our frigerator a MAGIC CHEF..the ice maker is the only thing we have replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from DULUTH, GA
- Parts Used:
- W10190935
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No Ice in bin.
Turned off ice maker. Remove one screw with nut driver (1/4") that hold plugin cover. Push the release lock, (up) on bottom of Ice maker to slide unit out enough to unplug and remove ice maker out of freezer. remove white side cover and replace control unit. Reinstall white side cover then plug unit in at freezer and slide unit into locks reinstall plugin cover with screw. Turn on ice maker and watch Ice maker start to move and tray to fill with water. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Van Buren, AR
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
ice maker not making ice
When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.
PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.
PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Volente, TX
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker quit working
Read on line that the motor module in the ice maker was likely to be the problem. I ordered the part and it came in as a complete module. All I had to do was to remove the cover, take out 3 philips screws, remove the old module and install the new one. I plugged it back in and had ice within the hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Ripon, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker stopped making ice.
Unplugged the frig., removed three screws, pulled the motor out, then slid the new motor in. Within a few hours I had ice again. The only problem was I felt the motor was still hooked to something after I took out the screws. Just be firm and pull it out, the pressure you feel is the thin bar that slides into the back of it to monitor the level of ice in the tray. It was REALLY easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Newbury Park, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Plastic wheel broken - Would not produce ice
1. Removed all 4 screws underneath with nutdriver
2. Whole assembly slides out like a drawer
3. Unplugged power/wire harness
4. Removed Motor Assembly - 3 screws
5. Found the broken plastic wheel
6. Ordered part on PartsSelect
(Total: 5 minutes)
7. Received new part next day
8. Put the new motor assembly back on using the original 3 screws (it doesn't come with new ones)
9. Slid unit back into drawer
10. Put the 4 Nut Driver Screws back in (tricky to get the wire harness cover back in place, but not that bad)
11. Plugged in wire harness
12. Turned on the ice-maker
Ice Dropped within the hour.
2. Whole assembly slides out like a drawer
3. Unplugged power/wire harness
4. Removed Motor Assembly - 3 screws
5. Found the broken plastic wheel
6. Ordered part on PartsSelect
(Total: 5 minutes)
7. Received new part next day
8. Put the new motor assembly back on using the original 3 screws (it doesn't come with new ones)
9. Slid unit back into drawer
10. Put the 4 Nut Driver Screws back in (tricky to get the wire harness cover back in place, but not that bad)
11. Plugged in wire harness
12. Turned on the ice-maker
Ice Dropped within the hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Sun City West, AZ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker not producing ice
I found your website while searching the internet for a repairman. My fridge was making strange clicking sounds and no ice. I suspected a certain part after reading the testimonials on your website. The part I ordered was delivered in less than a week and I installed it in less than 5 minutes. I probably saved about $200.00. Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Redwood City, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker stop making ice
Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from UNIONTOWN, OH
- Parts Used:
- WPW10190929
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker wasn't working (water line frozen) and showed extensive damage to the metal basin.
Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line
Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line
Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Mount Washington, KY
- Parts Used:
- 4318047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The old ice maker water valve washer in the water inlet port went bad and was leaking. Lasted for 35 years,
The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from VERO BEACH, FL
- Parts Used:
- W10190935
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Ice maker was not making ice
We replaced this part 5 years ago, so we considered ourselves "experienced" at this particular job. We followed the video at your site and after some sticky removal parts, we were able to put the new motor in and finish putting the freezer back in its original shape. After a few worried hours, we again had ice. The video was easy to follow and we couldn't be happier. Thank you for saving us hundreds of dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from LIBERTY, TX
- Parts Used:
- 4318047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
Ice maker wasn't getting water
Removed old water valve on bottom right back side of fridge installed new one which actually took less work
Was this instruction helpful to you?
Thank you for voting!