KUIO18NNVS1 KitchenAid Ice Maker - Instructions

Had repair man out to make repair his price for part $219.00 and $271.00 labor as he was looking up his price I got on line and found part here for $121.00 thought it might take me 1 hour to fix only 6- 1/4" nuts 2 screws and less than 30 min I had Ice maker working. Bottom line my total cost $75.00 repar man $121.00 part $196.00 that was a savings of $294.00

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

Fast after a little help from a friend

Wires in cutter grid were broken and wouldn't freeze/cut ice. Replaced with the new ice cutter grid that came completely assembled. Put it in with a screwdriver in less than 10 minutes. Ice cubes ready in 45 minutes. Repair guy told me it would be $455 for him to repair it. With shipping, mine was $133 and 10 minutes of my time. Well worth doing it myself.

Took out one strap support with a nut driver, unplugged the device and plugged in the new one. Reinstalled the support strap. Job complete.

Removal of old valve very easy and accessible, 2 screw/bolts for mounting, disconnect to electrical leads by hand, disconnect 2 plastic water lines with push/pull connectors and reverse order for installation. Total time-less than 5 minutes and basically no tools required expect pliers or nut drive to loosen screw/bolts. Just turn on and it was making ice

It was easy to remove the old grid and replace it with a new one.