KUIS18NNJB6 KitchenAid Ice Maker - Instructions

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Removed the back lower cover, behind the fridge. Uncliped the wiring. Removed the motor, (3 Screws).I did check the new motor before removal of the old one, to verify the older motor was the problem. After removal of the fan & motor. Removed the fan and placed it on the new motor, three screws later, plugged up the wiring, (I didn't changout the wiring, and the Refrigerator is good as new.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Over a period of weeks I watched my fridge grand to a halt. It was...saddening. I felt helpless, there was nothing I could do and I wasn't prepared to pull in a repairman. Upon it's departure from being affective (broke) I made up my mind to purchase a new one!! Flash-forward five minutes n the internet ...motivator by high costs, I altered my thinking and visited You Tube for a fix-it video. After a quick search I came across a clip that took me to the heart of the problem. It was THAT easy. Wow!! I followed the instructions and quickly learned the failure had to do with a small, light weight fan that's role was to pull heat from the condenser--it had ceased to work. While waiting for the part, I let a small fan blow on the condenser to dissipate the heat. The fridge roared to life!! Like a charm!! When the new fan body arrived I placed the blade from the old fan on it and installed it (the fan did not come with bolts and the holes were not threaded) using sheet metal screws. It immediately came started performing again and has been doing a superb job ever since. I easily saved $800 in costs going this route!!

I removed the two screws that hold the shield in front of the grid and put them aside allowing access to the grid. I then removed the two screws that hold the grid in place. I unplugged the connector and then pulled it out. I reversed the process to reassemble and powered up the unit. I now have ice again. This whole process probably took me 15-20 minutes to do the install.

remove the front cover by removing two screws. then remove two screws with a nut driver on each side. unplug the wireing harness from the top of the unit (may need pliers for this) the pull the unit out. then slide the new unit in, connect the wireing harness, install two side screws, and install the front cover and wham you will have ice in about 30 minutes. thanks parts select. you were very easy to deal with

I determined it was the cutter grid because there was a broken wire on the existing one. They have to heat up and cut the ice. I ordered it and the part was at my house in 1 day. The cutter grid part was easy to install. The ice maker is working great now.

Since no ice was forming on the evaporator plate, I first checked to see if I was getting water. Water to reservoir was fine, but it was not moving from the reservoir. Pretty logical that something was wrong with the pump. I pulled pump out. It was locked up, with a significant amount of calcium buildup. Replaced it and all works fine. Great ice again.

Removed old assembly by disconnecting 2 wiring harness connections and loosening 2 screws with nutdriver. Installed new assembly using same process. Had ice in about an hour. Very easy.

Simple, remove water reservoir (2 screws). Remove pump cover (1 screw). Remove 2 screws on bracket holding pump and unplug pump. My wiring was somewhat corroded and it took a bit of pulling to unplug. When you replace with new motor make sure to snap in new plug snug or it will not start up. Reassemble and away you go.Making ice no problem.

Wires in cutter grid were broken and wouldn't freeze/cut ice. Replaced with the new ice cutter grid that came completely assembled. Put it in with a screwdriver in less than 10 minutes. Ice cubes ready in 45 minutes. Repair guy told me it would be $455 for him to repair it. With shipping, mine was $133 and 10 minutes of my time. Well worth doing it myself.

Took out one strap support with a nut driver, unplugged the device and plugged in the new one. Reinstalled the support strap. Job complete.

I undid the bottom screws off the bottom front of the ice machine under the door... Knowing the water valve was at the front it made it super easy to get to and I didn't have to pull the machine out from under the counter etc. Turned off the water supply at the wall, disconnected that line at the valve, removed the line from the valve to the water reservoir. Unscrewed two screws that held it to the machine wall and put the new valve in, reconnected both lines and voila! Done! Running like its never run before. I filled up that reservoir for weeks by hand many times a day so the satisfaction is huge to have saved a fortune by fixing it myself! And I'm female which makes it even more satisfying. A monkey could put this part in. Anything a man can fix, I can fix too! Ha!