Models > KUIC15NRTS0 > Instructions

KUIC15NRTS0 KitchenAid Ice Maker - Instructions

Jump to:

All Instructions for the KUIC15NRTS0

Customer:: Jerry from Frisco, TX
Parts Used:: W11566405
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Water was not circulating to the freeze area

Easy. I took a picture with everything in tact. Took apart a couple of parts with screw driver. Replaced the pump. Put it all together and it worked fine.Thanks.

Was this instruction helpful to you?

Customer:: Sean from Simi valley, AL
Parts Used:: W10124096
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

condenser fan would not come on, and when it did, made loud noise.

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Was this instruction helpful to you?

Customer:: eBooks4u from Wimberley, TX
Parts Used:: W10124096
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench (Adjustable)

Noisy fan motor

Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!

Was this instruction helpful to you?

Customer:: Keith from Paducah, KY
Parts Used:: WPW10217917
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Water Leaking From Under Icemaker

Removed lower vent cover and removed valve. Removed water lines and power hookups and attached to new unit. Approx. 15 Minutes total repair. Checked for leaks. Finished. Part select had replacement valve to my door within 24 hours. Great service and simple to understand installation instructions. Highly recommend.

Was this instruction helpful to you?

Customer:: Scott from Phoenix, AZ
Parts Used:: WP2313637
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

our ice maker was not cutting the ice into squares.

I determined it was the cutter grid because there was a broken wire on the existing one. They have to heat up and cut the ice. I ordered it and the part was at my house in 1 day. The cutter grid part was easy to install. The ice maker is working great now.

Was this instruction helpful to you?

Customer:: Alfred from Hot Springs, AR
Parts Used:: WPW10217917
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Water Was Leaking Into The Control Board

I removed the inspection cover, removed 2 screws holding the control valve,depressed the realease rings on the water lines,unpluged the 2 electrical connections and removed the bad valve. I re-installed the water lines into the new part, reconnected the electrical plugs,replaced the 2 screws in the new valve keeper and replaced the inspection cover. Everything I received from partselect fit perfectly. Thank you partselect, the ice machine works great. I sure was glad you were there. Thanks,, alfred harvey

Was this instruction helpful to you?

Customer:: Missy from Naples, FL
Parts Used:: WP2313637
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Not making cubes

Wires in cutter grid were broken and wouldn't freeze/cut ice. Replaced with the new ice cutter grid that came completely assembled. Put it in with a screwdriver in less than 10 minutes. Ice cubes ready in 45 minutes. Repair guy told me it would be $455 for him to repair it. With shipping, mine was $133 and 10 minutes of my time. Well worth doing it myself.

Was this instruction helpful to you?

Customer:: Robert from Nashville, TN
Parts Used:: WPW10217917
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Leaking solenoid operated water value on ice maker.

Removal of old valve very easy and accessible, 2 screw/bolts for mounting, disconnect to electrical leads by hand, disconnect 2 plastic water lines with push/pull connectors and reverse order for installation. Total time-less than 5 minutes and basically no tools required expect pliers or nut drive to loosen screw/bolts. Just turn on and it was making ice

Was this instruction helpful to you?

Customer:: Lonnie E. from Canton, MO
Parts Used:: WP4387938
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Failed to Run

Checked Overload Start Relay With Volt Ohm Meter&Replaced Them Easy And Simple Repair

Was this instruction helpful to you?

Customer:: Paul from Paige, TX
Parts Used:: WPW10503764
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Ice maker would not make Ice.

Took out one strap support with a nut driver, unplugged the device and plugged in the new one. Reinstalled the support strap. Job complete.

Was this instruction helpful to you?

Customer:: Ronald from Flowery Branch, GA
Parts Used:: 2313702
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Under counter Ice maler not making Ice

Had repair man out to make repair his price for part $219.00 and $271.00 labor as he was looking up his price I got on line and found part here for $121.00 thought it might take me 1 hour to fix only 6- 1/4" nuts 2 screws and less than 30 min I had Ice maker working. Bottom line my total cost $75.00 repar man $121.00 part $196.00 that was a savings of $294.00

Was this instruction helpful to you?

Customer:: william from glen gardner, NJ
Parts Used:: W10124096
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set, Wrench set

Unit very noisy when running sometimes and then get quiet the noise would vary

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Was this instruction helpful to you?

Customer:: Atlee from Jupiter, FL
Parts Used:: WP2149705
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

broken light switch

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Was this instruction helpful to you?

Customer:: William from Fort Mohave, AZ
Parts Used:: W10124096
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

loud noise coming from back of fridg.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

Was this instruction helpful to you?

Customer:: Gene from Battle creek, MI
Parts Used:: W11566405
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

Recirculating pump stopped working

Remove ice tray and guard over moter. Un plug the 3 plugs and pull the entire motor assembly out. Use a screw driver to gently pry motor out. Snap in the new motor(the wiring was on the wrong side and the power cord coloring backwards on the replacement motor, but I snapped it in with the colors criss crossed and it worked). Re plug in the 3 plugs. Re mount mounting assembly, tray and then guard. Had a little trouble getting the tray back in. There is a little flap in the back that goes inside the tray. Other than that, a pretty easy fix.

Was this instruction helpful to you?

All Instructions for the KUIC15NRTS0