KUIS15NRTB1 KitchenAid Ice Maker - Instructions

Replaced the assy. But, I would have been happier if you sold just the wires. I could have replaced the wires at a much lower cost and may have taken less than an hour to replace the wires.Still happy - the ice maker works.

Removed old switch and installed new - but did not solve problem

We had the coldest winter in 114 years in north Texas (must be global warming...) and our outdoor kitchen ice maker value assembly frozen and cracked.

1) Remove bottom panel screws using nut driver
2) Remove door screws
3) Unhook two power connectors from value assembly
4) Release water supply quick connects
5) Replace value
6) Re-install door - this is a a little tricky there is a spring on each side which slows the door when opening and this pulls the door down which means the screw are not properly aligned by default. You basically have to pull the door up( a second set of hands help) and attach the screws and then let it go.

Simple remove the fan and motor, plug in the new cord and screw in the new motor.

pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that

I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

It was very easy. The part make look different online but it was a proper replacement.

removed two screws and bracket that held it in place. Removed the hoses and pump. put new one in by re-attaching hoses, pump then put screws back in to hold it in place. Fairly easy.

Double check the actual part number. While the item looks the same, my unit had a 3 prong plug while the replacement had only 2 and did not fit.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.

Replaced pump-loop cutting grid wire loosely around spacers-hold loose end with pliers-working from back to front remove all slack. Pull until piano string tight. Wire will not break if not linked. Tighten front screw.

I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

My top grid was broken. After removing the old wire and loosening the screws on both ends of the old wire, I carefully unrolled the new wire so there were no kinks. Next, I put one end of the wire in a vice to hold it in place. I put a loop in the other end and attached it to the one end of the frame. You can then hold the grid in both hands and put tension on the wire as you make the wraps. When you get to the end, attach it to the grid screw and tighten the screw while maintaining tension. You can then cut the remaining wire and reinstall the grid. I think this was much easier than the directions that came with the wire. Took 5 minutes to install the wire on the grid and 15 to 20 minutes to everything back together and start making ice.