106653522 Kenmore Ice Maker - Instructions

Removed old water valve on bottom right back side of fridge installed new one which actually took less work

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. The lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice maker. Gregg in PA.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was ice! Everybody was happy.

Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.

After locating the screws, removed icemaker, disconnected cable connection.

Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, connected wiring harness, tightened screws. Waited for ice to arrive about an hour later.

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

Removed bottem screw and loosened two top screws. Removed icemaker from support screws and disengaged cable. Replaced in reverse order. Total time was about 15 minutes.

Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.

. . . thanks!

Easy removel: remove one screw and loosen two others; unplug connector; swap actuator bar; replace

Unbelievable experience. Ordered on Friday received on Saturday. Removed three nuts with a nutdriver, unplugged the old icemaker, plugged in the new one and replaced the three nuts. I went from order to ice in the bucket in about 24 hours. Thanks

First I removed one screw that hold the element in place, lifted element about half an inch. I then pulled the element out about 2-3 inches and disconnected the wire. Then replaced two clips on top of element and re-connected the wire, put screw back and VUALYA....done!!!!!!!!!!!!!

I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.

I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice maker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.