7678894150 Kenmore Ice Maker - Instructions

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim

Replaced the control of the ice maker assembly.

I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!

Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.
Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!

followed instructions provided when ordering part

I played the install video a couple of times to assure myself that it was that easy. The video indicated that I actually had to remove the ice maker it install the motor module but in my case I did not really have to. I simply pulled off the plastic cover plate, removed the 3 phillips head screws and exhanged the new module for the old one. I turned the power and water back on and waited for something to happen...nothing did! After about 15 minutes and no noticeable electric or water flow activity I pulled the refrigerator out away from the wall to check the incoming water line and suddenly I heard water flow to the icemaker and within the next hour I had my 1st batch of cubes. Since then everything appears to be working and we have ice cubes for Christmas. All in all it was a pretty easy and inexpensive fix and probably saved me well over a $100.

Installed new motor control

I first turned off the refrigerator. I then used a hair dryer to melt and release the ice by warming the bottom of the mould. Then I turned the fridge back on and let the icemaker discharge the ice. I then turned off the icemaker and ordered the new part. I unplugged the fridge, removed the icemaker (three screws and an electrical connection). Then I replaced the heater/tray with the new one and turned everything back on. Within a couple of hours we began having ice again.

Took the front of the ice maker off. Noticed the arm inside was broken, found the part on your site and ordered it.....super fast delivery. Replace the moter assembly and off she went. had ice in about 30 minutes. Thanks for your services and I will highly recommend you to others......Thanks again.

The ice maker had quit before and I fixed it by taking it out to thaw.When it quit working the second time thawing it out didn't do the trick.The dispenser still worked so we were buying bagged ice. The dispenser lever fell apart and my wife said fix them both or "I'm calling a repairman." My in-laws recently had a bad experience with an appliance repair service and my motto is that "if it's already broke I can't hurt it anymore" Found the Parts Select site and started reading everyone instructions. During the summer,our electricity had went off several times,so I figured that the icemaker control and motor assembly was the problem. Watched the installation video,and followed the instructions. Used parts diagrams and super glue to piece dispenser lever back together. Wife is happy and we saved $

first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!

I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks

Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.