UKI2000AXX Jenn-Air Ice Maker - Instructions

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than the one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

I read the instructions from your site, removed the old unit, salvaged the parts to be reused and reassembled. 1/2 hour later I had ice and no leaks.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

Ordered new part by the numbers and pics. and installation was so easy. I thank you very much

used 1/4 inch wrench to remove bottom screw
and loosend tip screw and removed valve wires and water line

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

I opened the box, unwrapped the new ice pan, gave it a cursory rinse, and put it in the freezer.

Repair for the most part is very easy! With the particular assembly that I purchased you MUST keep the cord, the wire piece that tells the ice maker when tray is full and the front cover from the previous part. Removal is easy. Flip wire piece up. Remove ice holder. Remove screw at bottom of assembly. Push assembly up not to hard as you don't want to break the clips attached to the fridge. Pull out far enough to disconect white cord at the fridge connection. Piece removes easily. I actually had a little ice build up in the white hose that dispenses the water. I took a cup of warm/ hot water and held up to hose to melt ice. To put back in just do it in reverse. Remove the 3 parts previously mentioned. Put on the new assembly. It was a little tricky getting the clamps to click into place. Just go slow and push upwards and towards fridge wall. This is definately worth trying yourself before calling a repair man! Good luck. Hope this helpful.