JIM158XBRB0 Jenn-Air Ice Maker - Instructions

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

Fast after a little help from a friend

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

I called the 800 number and the lady was great to work with and helped me thru all the order process and confirmed the numbers. She also told me she would try to get the order out that day which she did and I had the part two days later. When it arrived I went to the web site and reviewed the video and went to work and all went as the video said. Thanks for the help and if i need another part I will visit your site or call.

I watched the film on installing and taking out. Step by step. easy.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Took out one strap support with a nut driver, unplugged the device and plugged in the new one. Reinstalled the support strap. Job complete.

Wires in cutter grid were broken and wouldn't freeze/cut ice. Replaced with the new ice cutter grid that came completely assembled. Put it in with a screwdriver in less than 10 minutes. Ice cubes ready in 45 minutes. Repair guy told me it would be $455 for him to repair it. With shipping, mine was $133 and 10 minutes of my time. Well worth doing it myself.

Removal of old valve very easy and accessible, 2 screw/bolts for mounting, disconnect to electrical leads by hand, disconnect 2 plastic water lines with push/pull connectors and reverse order for installation. Total time-less than 5 minutes and basically no tools required expect pliers or nut drive to loosen screw/bolts. Just turn on and it was making ice

It was easy to remove the old grid and replace it with a new one.

I removed the inspection cover, removed 2 screws holding the control valve,depressed the realease rings on the water lines,unpluged the 2 electrical connections and removed the bad valve. I re-installed the water lines into the new part, reconnected the electrical plugs,replaced the 2 screws in the new valve keeper and replaced the inspection cover. Everything I received from partselect fit perfectly. Thank you partselect, the ice machine works great. I sure was glad you were there. Thanks,, alfred harvey

Checked Overload Start Relay With Volt Ohm Meter&Replaced Them Easy And Simple Repair

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.