IC3Q-IC3Q-ASSMBLY Amana Ice Maker - Instructions

We replaced this part 5 years ago, so we considered ourselves "experienced" at this particular job. We followed the video at your site and after some sticky removal parts, we were able to put the new motor in and finish putting the freezer back in its original shape. After a few worried hours, we again had ice. The video was easy to follow and we couldn't be happier. Thank you for saving us hundreds of dollars.

Removed old ejector arm and installed new part.

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

Replaced Icemaker

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Turned off ice maker. Remove one screw with nut driver (1/4") that hold plugin cover. Push the release lock, (up) on bottom of Ice maker to slide unit out enough to unplug and remove ice maker out of freezer. remove white side cover and replace control unit. Reinstall white side cover then plug unit in at freezer and slide unit into locks reinstall plugin cover with screw. Turn on ice maker and watch Ice maker start to move and tray to fill with water. Done.

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.

Your youtube ..order part and fix in 2 mins.AWESOME we had our refrigerator since 1983.... my wife keeps her looking new...& happy with the saving .Our frigerator a MAGIC CHEF..the ice maker is the only thing we have replaced.

Arrived soon than expected. Unplugged some wires, removed face plate, 3 screws--install and do reverse.

Easier than I would think---Saved $150- to have someone else do it.

Works fine.

I performed basic troubleshooting to make sure there was power and water. Based on historical research on this particular ice maker, I decided that the best direction was to replace the entire assembly. I found this item on this site, ordered it and received it a few days later. I basically removed the ice pan and a few items in the freezer, removed the three mounting screws with either a flat blade screwdriver or nut driver, pulled the electrical harness out of the back wall of the freezer and transferred it to the new ice maker and then installed the new unit, really that simple. Iwas concerned at first, not seeing any activity in the new ice maker but after 15 minutes or so I heard ice falling into the ice bin. Well worth replacing seeing how simple this job was.

Removed the elec connection (after unplugging app) found it easier to remove from appliance. Remove the three screws ( do not temove,....just loosen, the top two) bottom must be removed! Insert the power connection, exchange the tilt up rod, line up the water connection and place back on the two top screws. Tighten and relpace the bottom screw. I found out the hard way.... you cant't see the two top screws . The slots on the ice maker just fit over the screw heads.... it's cold in there!!!

Hopoe this helps..

Cape Cod

The video of the installation was the best help I have ever had. Rather that vague written instructions that are usually so poorly written they are of no help, the video showed exactly how to do it. I wish everyone provided videos like this!

after reading reviews on changing the control module I decided it couldn't be very difficult. I was rewarded because it wasn't. It took less than 20 minutes to change the module. At first I was concerned because the wheel did not start turning as soon as power was connected. I discovered this is normal and 30 minutes later the icemaker was making ice again. Simply remove the 3 screws, carefuly pull the module away from the shutoff arm, and pull it out. putting the new one in is the exact reverse. You just have to realign the ejecter cam in the icemaker with the new module so it slides right in.

After reading the stories on your site, I figured it had to be the motor control. Easy to take off, but had to take the tray off the freezer wall to get the ice out. Once I did that it was a piece of cake. Now I have ice (and vodka tonics...).