IC4R-IC4R-ASSMBLY Amana Ice Maker - Instructions

I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.

This was a very easy fix. I took the old ice maker out, including the electrical harness. Switched the harness and stop bar to the new ice maker on my bench, then installed the new assembly. Ice initially had some hollow cubes. I checked the ice maker for level. But it was fine. Thought it might be moving too fast. But it seems to have cleared up. Perhaps it took some time to completely cool down.

First I disconnected the refrigerator. I snapped off the service door. taped closed the auto.door shut off located on the left side wall. the unit just pulled out,
disconnecting the power source, removed the plastic cover, unscrewed (3) screws and reattached the new unit . i reconnected the process in reverse.
if i had repairman do this it would have cost twice as much .

1. Removed all 4 screws underneath with nutdriver
2. Whole assembly slides out like a drawer
3. Unplugged power/wire harness
4. Removed Motor Assembly - 3 screws
5. Found the broken plastic wheel
6. Ordered part on PartsSelect
(Total: 5 minutes)
7. Received new part next day
8. Put the new motor assembly back on using the original 3 screws (it doesn't come with new ones)
9. Slid unit back into drawer
10. Put the 4 Nut Driver Screws back in (tricky to get the wire harness cover back in place, but not that bad)
11. Plugged in wire harness
12. Turned on the ice-maker
Ice Dropped within the hour.

Unplugged the frig., removed three screws, pulled the motor out, then slid the new motor in. Within a few hours I had ice again. The only problem was I felt the motor was still hooked to something after I took out the screws. Just be firm and pull it out, the pressure you feel is the thin bar that slides into the back of it to monitor the level of ice in the tray. It was REALLY easy.

I found your website while searching the internet for a repairman. My fridge was making strange clicking sounds and no ice. I suspected a certain part after reading the testimonials on your website. The part I ordered was delivered in less than a week and I installed it in less than 5 minutes. I probably saved about $200.00. Thank you!!!

By replacing it with a new ine maker.

Very easy to install the new ice maker. Removed the bottom screw holding the ice maker to the side of the freezer. Loosened the top two screws. The old ice maker came off just like that. Unplugged the power supply from the freezer and removed the whole apparatus.

I saved the wiring harness, screws, cover, and metal arm from the old ice maker. Installed these on the new one and mounted the new ice maker in the freezer. Done.

The only issue I had was that the water supply hose got kinked when I pushed the fridge back into place. Once that was resolved, the new ice maker started happily making ice.

Removed old ejector arm and installed new part.

Your youtube ..order part and fix in 2 mins.AWESOME we had our refrigerator since 1983.... my wife keeps her looking new...& happy with the saving .Our frigerator a MAGIC CHEF..the ice maker is the only thing we have replaced.

Remove bottom screw loosen 2 top screws unplug connector from back of icebox. Lift up and pull forward. Swap front cover full bucket stop bar and wire (plugs in) reinstall 10 minute job

the diagnosis was the most difficult step.. and trusting that the one visible nut was the only thing holding it on.. (there are 2 other clips that you need to use a little force on to detach). remove the ice maker (one nut, 2 clips, detach plug).. then remove the 3 screws holding on the 'face' , pry face off, you will see where the 'contact' has burned/melted/worn away. replace unit. 80% of the time, this is the problem (according to my research)

Five minutes with a phillips screw driver and the cube maker was changed. . . In the process, I failed to unplug the unit, and shorted the fill valve in the back. Again, five minutes with a nut driver and it was changed. No need for a PHD or the cost of a service technician for either job.

Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.