IC3N (P1110701W) Amana Ice Maker - Instructions

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

The swap was quite easy. All I had to do was remove 3 nuts and unplug the flat wire connector. I kept the old unit when I took it out in case I needed any parts, but the only thing I needed to transfer over was the Ice level wire. Very straightforward!

Three screws holding the ice maker unit, one quick disconnect wiring harness.
Replacement was simple.

turned off the power. took out the bottom scerw and loosened the top two screws. lifted out the old ice maker which allowed enough room to unplug the power cable from the back of the freezer. put the cables and bucket fill rod on the new unit and installed the same way it came out. turned on the power .closed the door and waited for the ice maker to cycle. it takes about 20 minutes; the ice maker has to get down to the proper temperature,

Trouble shooting was the difficult part. All advice was to replace the valve but water did not leak with icemaker removed. Found the release coating in the icemaker tray had cracked and peeled away. Since this is also the water seal, the tray would drip water after filling, before freezing. The new icemaker solved the problem.

After being scammed by a repairman who charged for repair that didn't work, then promised to order replacement, then said he couldn't get it, I was pleased to find your site. Ordered the part, watched the installation video,received the part within two days, replaced it in 10 minutes--it works perfectly. I only wish I had looked on internet before calling repairman recommended by my dealer.

Removed the old ice maker by disconnecting the wiring harness, loosening to side screws and removing a third screw under the ice maker. Installed the new ice maker following the above instructions in reverse order. Ice maker started working after about 30-45 minutes (probably for the tray to get cold enough). It was a very simple process. Thanks.

I pulled the old one out and went on-line to find a part. Once I found the right sight that had the part I ordered it and had it shipped to my house. When the part came in just a few days I installed it and now it's working just fine......

Initially I turned off the power to the unit ( I found no need to disconnect water source. I believe it is controlled by the unit and is in the "off" position when powered down) then I loosened the top two screws, removed the bottom screw and slid the unit off of the upper mounting screws. Taking a flat screw driver blade I pushed down on the connector's locking nib within the maker and released the connector. I then reversed the procedure to reinstall making certain that the connector was fully pushed in. Tightened things down, turned on the power and had 'cubes" in about 1 hour. Easy fix, "repair" stories on site make this incredabily simple.

I followed your video which made the whole repair/replace-
ment simple !