CP320W Jenn-Air Grill - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jose from Victor, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The switch would not turn off the range. The switch just kept turning but nothing happened.
I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything worked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bourbon, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sparks shot out from under knob, then, no surprise, the burner didn't work
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentine from Bow, NH
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from castle rock, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
electric element would not function
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Centreville, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Infinite Rotary Control Failed
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.
gc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Valley Grande, AL
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
back burn would turn high no mater where you set the control knob.
Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Rosebush, MI
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one of the four burners was not working
Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lorton, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
RF burner would not heat
1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bowie, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
One burner only heated to a high temperature.
I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from harlingen, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no heat to burner
Removed top and front panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanna from St. Johnsbury, VT
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front right burner did not turn on
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Two Rivers, WI
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad burnes off on switch
Easy as Pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Collegeville, PA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Woodland Park, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Port aransas, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rear Burner Was Not Functioning
Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.
Was this instruction helpful to you?
Thank you for voting!