FFSS2615TP0 Frigidaire - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
2 broken shelving supports
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Anderson, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Buffalo Grove, IL
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from BRONX, NY
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
evaporator coil would freeze up solid. no air flow through coil; no cooling.
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from ORANGE, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker quit working
Followed the steps in the video on your site, really easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Herington, KS
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from ASHEVILLE, NC
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Crisper Supports broken
Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from New Orleans, LA
- Parts Used:
- 241885001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Original gate broke at the swivel point
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lyman from LEXINGTON, KY
- Parts Used:
- 242303001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge side warm.
Removed the nut screws holding on the controls on the fridge side. Swapped out the old damper control for the new. Just need to be sure to get the new assembly in the same way the old one came out -- including placement of the freezer sensor control (separate part from the assembly). Replaced the control unit and damper worked and now my fridge is the right temperature! One other item -- when diagnosing the problem with a warm fridge, most newer fridges have a self testing method via the digital temperature controls. Find your Service Data Sheet for instructions. This would have saved me time from using my multimeter testing various components.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANET from NEW FAIRFIELD, CT
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice Maker Doesn't Make Ice
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Kissimmee, FL
- Parts Used:
- 241786001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked gasket
Took off old gasket and pressed in new one. Took about 5 minutes for both procedures. Vey Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Langley from Delberton, WV
- Parts Used:
- 241786001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced door gasket
I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Brooklyn, NY
- Parts Used:
- 240351601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom refrigerator door shelf bin broke.
The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.
Was this instruction helpful to you?
Thank you for voting!
Plastic fan broke
took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from PEORIA, AZ
- Parts Used:
- 241969501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
Fairly simple
By hand after removing the other shelves.
However, a day later it broke in the same way as the original one broke. It is plastic and not strong enough for supporting the vegetable drawer. This is the third one to not stand up to normal use. I would not recommend this unit to anyone.
However, a day later it broke in the same way as the original one broke. It is plastic and not strong enough for supporting the vegetable drawer. This is the third one to not stand up to normal use. I would not recommend this unit to anyone.
Was this instruction helpful to you?
Thank you for voting!