FFHG2250TD0 Frigidaire - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from MARANA, AZ
- Parts Used:
- A13402902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced water filter with bypass because water supply to appliance is already filtered by reverse osmosis
Remove filter by twisting counter clockwise
Install bypass by twisting clockwise
Install bypass by twisting clockwise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert E from MILL HALL, PA
- Parts Used:
- 240597203
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Warm refrigerator temperature
Did not repair, sensor was not located where you said, wrong sensor was sent to me, can't return oe exchange it COSTERMER SERVICE WILL NOT ANSWER MY EMAILS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Olden, TX
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Marco Island, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was over filling.
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Eastlake, OH
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Fridge leaked water all over my kitchen
I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LANCASTER, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
LEAKED WATER AFTER USING WATER DISPENSER
DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from KING, NC
- Parts Used:
- 5304508043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shelf roller broke from shelf
Once I found out how the roller was part of the shelf and not the rail I replaced the broken shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from W HENRIETTA, NY
- Parts Used:
- 5304508761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the frame that holds the wheels broke off to the food drawer
had to take off a few pieces to the old frame and put it on the new one that held the drawer on the support bracket so it would be put back in the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from GANSEVOORT, NY
- Parts Used:
- 5304508042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
roller guide on shelf broke
after getting the correct part all that was needed was to remove several screws for the holding brackets to attach that bracket. also had to remove and place rollers on new part. not very difficult but took a minute to line up screws correctly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARLYN from GOSHEN, IN
- Parts Used:
- 5304508043, 5304508042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The guides or wheels had broken of so all I needed to do was to screw them in place on the new part.
I screwed the old wheels that came off on to the new part. It took less then 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus M from MONROE TWP, NJ
- Parts Used:
- 5304508761, 5304508016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
cover was cracker.
THE repair very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from REEDS SPRING, MO
- Parts Used:
- 5304510280, 5304508042
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
Roller support on COVER snapped.
At first I thought it was the support from the diagram. Not easy to get a visual 3d LIKE OTHER WEBSITES have. Current diagram looked like all I needed was the Bin. then found out I needed the cover which was an extra 100.00.
I was not happy. Theres nothing to tell you how to replace 24b part per diagram on website. You have to remove both left and roght shelves connected together and then unscrew, replace, etc,. Again no instructions on how to replace such said item.
Because of this I rate very low.
I was not happy. Theres nothing to tell you how to replace 24b part per diagram on website. You have to remove both left and roght shelves connected together and then unscrew, replace, etc,. Again no instructions on how to replace such said item.
Because of this I rate very low.
Was this instruction helpful to you?
Thank you for voting!