DGHF2360PFBA Frigidaire - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TIM from W HENRIETTA, NY
- Parts Used:
- 5304508761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the frame that holds the wheels broke off to the food drawer
had to take off a few pieces to the old frame and put it on the new one that held the drawer on the support bracket so it would be put back in the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from SHINGLETOWN, CA
- Parts Used:
- 242015201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Scratch on stainless frig door.
Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARLYN from GOSHEN, IN
- Parts Used:
- 5304508043, 5304508042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The guides or wheels had broken of so all I needed to do was to screw them in place on the new part.
I screwed the old wheels that came off on to the new part. It took less then 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from STATEN ISLAND, NY
- Parts Used:
- 5304501270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer was causing frost and ice
i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from FAIR OAKS, CA
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Ice maker not making ice
Located problem part of ice maker on web site. Picked the part that had the highest percentage of being the the part that was broken (58% I think). Removed the part, waited for the new part, then put it all back together. Simple. It works great. Thanks for having such an easy web site to diagnose the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from OLATHE, KS
- Parts Used:
- 242009602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from POTTSTOWN, PA
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER
VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARTINSVILLE, VA
- Parts Used:
- 5304508043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
R/S fruit & vegetable drawer L/S roller holder broke.
I removed the r/s drawer, removed the r/s shelf, transferred the metal brackets to the new shelf & reversed the procedure to reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from FREE SOIL, MI
- Parts Used:
- 5304507976
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide assembly broke on left side of freezer drawer.
Took front of door off, took out freezer basket removed one screw, took off old part and put on new part, put everything back together and it was done. 15 minutes done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WINDER, GA
- Parts Used:
- 5304508270
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.
Simple tightening of the screw with the right tool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PASADENA, MD
- Parts Used:
- 5304508043, 5304508016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Removed old rail installed new rail
Removed screws and rail and installed rail and screws
Was this instruction helpful to you?
Thank you for voting!