CFLE1011MW2 Frigidaire - Instructions

I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!

remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry

after removing the panel covering the dryer blower and removing the blower cover, i pulled the old blower wheel off and placed the new whell on carefully lining the flat edge of the wheel hole up with the flat edge on the blower piston, the n i placed the clamp on and put back all the housing covers and panels...and now my dryer runs quiet and drys cloths fast....thanks to partselect!!!!

My Husband did the repair it took less than 15 minutes. He popped the front off the washer. He then unscrewed two screws and removed the pump assembly. He popped the new pump in, and put in the tow screws. Then he put the washer front back on replacing two screws. It took all of five minutes. I am so pleased it was so easy. I told him next time I'd do the repair and he could watch!
Lil

I got online and found that everyone was charging a king's ransom for a piece of plastic. Your ransom was slightly less. Then I paid $7 shipping and handling for the part which came packed in a box six times its size...I guess all that cardboard costs a mint. I opened the box, removed the lint filter, and put it into my dryer....voila! No more holes!

It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

first i used a flathead to lift up the top of the dryer. there were two prongs that you press in to detach the top.

then there were two screws on the inside along each side that i needed a phillips to remove. one screw on each side.

i also needed to detach a cable and cut the tie.
from there, it was easy to pull off the front of the dryer.

the first noticeable thing was HOW much lint there was inside! so out came the vacuum and away went all the dust and lint.. a TON of it.

then i used a sharp knife to remove all the existing upper and lower felt. that took awhile, and i got as much as i could.

then i applied the TOP felt, nice and center, and from there, the FELT was applied, which fit perfectly. I let it dry/set for about 2 hours.

for the Front drum glide, AN IMPORTANT NOTE! i ordered only ONE drum glide, but you need TWO! I had to order a second one, and i dont know why they dont come in pairs.. so the front drum glides snap on pretty easily to the front of the drum. press hard and they SNAP into place. once they are snapped on, you just put back on the front, replace the screws, re-connect and re-tie the cable, and close the lid!

Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

First pry up on the front edge of the top panel of the dryer which is held in place by snap in clips. Pivot the top open and support against wall or other taking care not to pull on wiring harness. Next remove the 2 screws that hold the front panel in place. These are located on the inside of the front panel. The front then snaps loose also. Remove the plastic drum stop located at the top edge of the front of the dryer. Next I removed the 3 drum screws located inside at the back center of the dryer. Next you can you need to remove the belt the motor located at the rear vent panel on the back. Slide the now loose drum out exposing the rear bearing. With a 5/16 end wrench, loosen the 2 screws on either side of the bearing retainer. Assemble the new bearing bracket to match the old one. Apply a liberal amount of supplied lubricant to the pivot ball and plastic retainer. At this point it was helpful to have someone at the rear of the dryer hold the new retainer bracket against the back of the dryer while I tightened the new bearing assembly in. Assemble dryer in reverse.

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, put the hoses on, plug in motor and replace front panel. plug into wall

First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no handy man so thats how easty it was.

I read the others repair story and it was a easy repair, my wife had a repairman come out and check it already, he stated to her that it was a major repair and that he needed to take it to the shop for repair, well he was full of sh##!!! The unit is a stackable washer dryer,if the screws inside the drum backout, the belt comes off and caused mine to brake the belt,my wife found the 2 small screws in the bottom of the tub,theres a small cover on the back that you remove and you can see belt drive pully! Follow the directions that have been explained on others listed it"s easy!!! Mike

I've always been a "do it yourselfer". If I can fix it, I save money. I took the dryer apart by lifting the top up like car hood. Then I removed the front panel. The front drum glide snapped into place easily where the other one had broken off. The felt strip that you sent was much shorter than the one on the dryer, so once I used the wire wheel to remove the old glue, I cut off the section of the felt that was bad and replaced it with the new felt. The turns much quieter and clothing doesnt get caught behind the drum anymore.

1) Unplug the unit.
2) Remove all screws from top of the unit except for the one in the center front that does not go through the outer casing.
3) Find the Thermal Limiter which is on the back wall near the top on the left side when looking from the front.
4) Disconnect the two wires
5) Remove the two screws that mount the limiter to the back wall.
6) Use an ohmeter to test if a current flows through the unit. If no current flows through (an open switch), then the unit will need to be replaced.
7) Clean any lint that you can at this point.
8) Use two screws to mount new Thermal Limiter
9) Reconnect the two wires to the Limiter.
10) Attach the top of the dryer case.