Models > EV171NYMS03 > Instructions

EV171NYMS03 Whirlpool Freezer - Instructions

Jump to:

All Instructions for the EV171NYMS03
76 - 90 of 131
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Arlington, MA
Parts Used:
W11384469
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Apopka, FL
Parts Used:
W11700559
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
no ice maker at all
We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Petersburg, AK
Parts Used:
W11700559
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Wrench set
Wrong valve bracket
I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christine from Burnsville, WV
Parts Used:
W11700559
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver
The wire harness plug was male .Same as the plug on the refrigerator
I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BreathMinder from Merritt Island, FL
Parts Used:
W11700559
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Didn't work once installed
Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Manchester, NH
Parts Used:
W11700559
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Wrench (Adjustable)
whirlpoolAuto Ice maker not working
Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sheri from Muskogee, OK
Parts Used:
W11700559
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
never had an icemaker attached
My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from San Diego, CA
Parts Used:
WP4357142
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Freezer door was not sealing
Removed door. Laid door down on a table. Unscrewed all screws around outside of door. Removed plastic cover back of door underneath cover was filled with heavy ice apparently from condensation. Cleaned and dried back of door really well. Replaced with new seal. Reinstalled door. New seal works perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Boerne, TX
Parts Used:
WP4357142
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Freezer was icing up on interior - faulty gasket
I unplugged and defrosted the freezer ( good excuse to give it a good cleaning). I then removed the hex screws from the door under the gasket. Because this attaches the door panel to the freezer, it is helpful to have two people for this task if you have a full size upright freezer. We then removed the panel, cleaned the door, and fitted the new gasket in place. If your gasket has kinks in it, either throw it in the dryer on low for a few minutes or use a hair dryer to smooth them out. We then added a few screws around the center point of each side to hold the gasket in place, secured the corners, and replaced the remainder of the screws. We used a small cordless drill. The gasket will be hard at first, so I duct taped the freezer door shut with a few pieces of tape and turned the unit back on. A repair guy was going to charge me $350.00 for the job, but I did it for free with the cost of the gasket. This site is the least expensive place I found anywhere, and shipped very quickly!
Was this instruction helpful to you?
Thank you for voting!
Customer:
oliver from tampa, FL
Parts Used:
W11700559
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
old ice maker the ice cubs keep freezing togather
replaced old one installed new one
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bryan from Albuquerque, NM
Parts Used:
WPW10445742
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Fan blade had a broken blade. Did it ever make a lot of noise when running as the broken blade cased the whole freezer to vibrate.
Removed panel and replaced the fan and clip when it arrived from PartSelect. The job was not big but having a part outlet with the item in stock was a real joy. In a few days we were back with a silent running freezer. So quiet now that I have to open the door to confirm that it is still running. Thanks Part Select. Bryan L. Huth
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN from VERO BEACH, FL
Parts Used:
W11700559
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Small leak from icemaker
Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Lawrenceville, GA
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Light switch which turns on the lights when the door opens went out
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Fairport, NY
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paula from Rush, NY
Parts Used:
W11384469
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the EV171NYMS03
76 - 90 of 131