5VEV188NAS00 Whirlpool Freezer - Instructions

replaced old one installed new one

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.

I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!