EV171NYMQ03 Whirlpool Freezer - Instructions

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

First filled tub with hot water and placed new gasket in water to limber up. Removed Door, placed on a table, removed all screws and removed door insides and old gasket, Cleaned all parts, dried new gasket then put back together just in reverse of removal, moved fridge back into place turned back on and it was cooled back down in about 15 min. working great. Now it has the same vacuum on it as when it was new.

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

put the new gasket in a tub of hot water. remove door and lay on flat surface, remove old gasket and pull hot gasket from tub, dry and install, the hot water helps remove the wringles from shipping.

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

removed food from freezer, removed 4 screws from access panel, removed panel, removed fan assy, removed blade and replaced with new blade assy. the new blade assy will not allow this to be a problem again. replaced panel and screws. replaced food in freezer. Took longer to femove and replace food than it did to replace the blade. I unplugged the freezer before I began.