TFU14F7EW0 Tappan Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cynthia from Keystone, NE
- Parts Used:
- 297181900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light burned out on the door lid
Used a thin screwdriver to lift out the burned out light assembly. Unplugged the old light unit and installed the new one. Plugged in the freezer and the light worked. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha M from Fort Worth, TX
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle broke off the door
We removed the trim and the screws and kept them in a safe place until the handle arrived. It took only about 10 minutes start to finish. Very Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Buffalo, MN
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Evaporator freezing up. Noticed Ice cream not frozen solid
Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- felder from logansport, LA
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle
backed out screws from old handle, install new hansel w/ same screws & screw cover. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Kilgore, TX
- Parts Used:
- 5304464438, 216008900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
compressor wouldn't start
I used a pick to remove the lugs from the old starter. Clicked them right in the new one and it went to woking!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Yulee, FL
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coils not Defrosting and stopped freezing
Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from Jackson, GA
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
Remove cover on handle, and unscrewed the old handle. Then reversed procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott J from Westminster, CO
- Parts Used:
- 301036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Side rail for sliding shelf would not stay tight
The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from petaluma, CA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Woodstock, GA
- Parts Used:
- 5304442620
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fan in freezer quit
This was an easy job. First remove the ice maker, if you have one. Mine was mounted with just two screws. Loosen these screws, unplug the power cord at the connector and then lift the ice maker off. Remove the light bulb cover and the light bulb, just so you dont break it. Remove two hex screws and the back cover can be removed. My fan was mounted in the middle of a bracket retained between two rubber bushingings. Just push the fan blad of the shaft and pull the motoer out. Dissonect the power cord at the connector. My moter was differant than the replacement on the mounting so with the removial of the two screws on the motor I was able to exchange the upper and lower cast motoer housings. Reverse the assembly process and you good. Mine is running great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from springfield, GA
- Parts Used:
- 216008900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
awasome
After reading reviews I was not sure but I ordered part on Wensday in the AM and I had the correct part Thursday evening this company rocks thank you by the way i paid for regular shipping I will order again in a heartbeat
Was this instruction helpful to you?
Thank you for voting!