TFU20F7EW0 Tappan Freezer - Instructions

first removed two screws that held handle. Then replaced. Ordered a motor 3 years ago from land office with verbal over counter instructions and that was easier but to get part this time was very simple ! With the model number and name brand input on site I had part in 3 days instead of waiting for a chance to visit land store and HOPE they had the part. Y'all might consider a zoom feature for us older folks.

I was surprised that the screws and trim piece were not included so make sure you have them from the old handle or order new. First removed the broken ends still on the freezer. I removed the small metal brackets from the old handle and put them on the new one, screwed the handle to the freezer and put the trim piece on. Real easy.

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

Used a thin screwdriver to lift out the burned out light assembly. Unplugged the old light unit and installed the new one. Plugged in the freezer and the light worked. Easy as pie.

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

We removed the trim and the screws and kept them in a safe place until the handle arrived. It took only about 10 minutes start to finish. Very Easy!

After reading reviews I was not sure but I ordered part on Wensday in the AM and I had the correct part Thursday evening this company rocks thank you by the way i paid for regular shipping I will order again in a heartbeat

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

I first noticed my ice cream getting soft. Then 2 days later the alarm went. I emptied the freezer, opened the panels and saw no frost. I saw that 99% of issues were resolved with a defrost timer and thermostat so I ordered those. I have to say the parts came quickly and they went in very easy. My freezer seems to be in the 1% category though. It's still not cooling even though I can measure the temperature at the front of the evaporator coil is cold but by the end of the coil it's almost room temperature. I think a repairman is called for.

Ordered freezer key friday afternoon received it saturday afternoon. Fast service

Remove cover on handle, and unscrewed the old handle. Then reversed procedure

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

The handle for the freezer arrived the next day. Most of the time repairs at home are alway a challenge. But the handle was placed where it belonged in about 5 minutes.It was the easiest repair we ever had and now we don't have problemes opening the freezer. Thanks so much.