MQF2056TEW01 Maytag Freezer - Instructions

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Open the door put shelf in it fit perfectly. Thanks

Removed panel and replaced the fan and clip when it arrived from PartSelect. The job was not big but having a part outlet with the item in stock was a real joy. In a few days we were back with a silent running freezer. So quiet now that I have to open the door to confirm that it is still running. Thanks Part Select. Bryan L. Huth

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

removed food from freezer, removed 4 screws from access panel, removed panel, removed fan assy, removed blade and replaced with new blade assy. the new blade assy will not allow this to be a problem again. replaced panel and screws. replaced food in freezer. Took longer to femove and replace food than it did to replace the blade. I unplugged the freezer before I began.

I had the best luck using pliers to remove the hex top screws. Once the screws were removed I unplugged the old defrost timer and plugged in the new one. Replaced the screws and the freezer worked when plugged in.

Had to remove 3 trays of food to get to the panel where the fan was, remove 4 phil screws found the fan had a broken blade. Went on line found the part at partselect order it recived it in 3 day. Removed the fan had 2 screws use nutdriver, removed old fan blade install new put everything back freezer is working fine.