1069209481 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Titusville, FL
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Hinges were making a popping sound and did not close properly
I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Columbai, MD
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Original cam broke into 3 pieces
Part arrived overnight. The How-To video at PartSelect showed the procedure exactly. It took about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from haddon heights, NJ
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
refrigerator door did not seal and was out of alignment
I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus shipping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Beaver Dam, WI
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jess from Manchester, TN
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door not closing tightly
Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ramona, CA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
refrig door was clunking when opening &closing.
rem upper hinge on door on & lifted door off. installed kit provided & ressemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Englewood, CO
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge door wouldn't close by itself
I removed the door (three screws on top). Flipped the door upside down, removed the cams, and replaced with the new ones and replaced the door. Now the door closes great. The only problem is that the door sort of "clunks" into place when I open or close it. I am not sure that I used the right cams. The drawing on the directions was not at all clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ft. Myers Beach, FL
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
cams on lower hinge fractured and door wouln't close
1. Used fine tip marker pen to draw outline of upper hinge position
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Sun City, AZ
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The refridgeror side was not cold enough
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Reading, PA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Plastic door cams wore away over time
I removed the door and replaced the door cams and reinstalled the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Salt Lake City, UT
- Parts Used:
- 4318165
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broken bottom door hinge, clunked when opened
I am a single female so the hardest part was lifting the door off and then trying to get it back on the hinge. I used the same bolts that were on the door so putting the new parts on was the easiest part. The slowest part was finding the right socket for the bolts and unscrewing the originals. Beats hiring a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard H from Mason City, IA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Teflon lower cam broke into from wear
removed door,removed worn part and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Harrisonburg, VA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Popping noise when opening and closing door.
The parts were delivered promptly. I ordered the kit assembly because I didn't know which part was the problem. Reading the remarks from other people's symptoms and solutions made the process much easier. I replaced both the upper and lower cams. Lubricated the cams and reinstalled the door.. Problem solved!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Prairieville, LA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door would not swing shut on its own as normal.
Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Little Falls, NY
- Parts Used:
- W10822278
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy defrost timer
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this instruction helpful to you?
Thank you for voting!