1068265911 Kenmore Freezer - Instructions

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

I found this part on PartSelect. I was so excited it also showed a video on how to fix the door. My neighbor said he would help me and I ordered the pkg. It took 3 days to get here since I ordered Friday night and the part arrived Tuesday , this was the Easter Sunday week end also. Well the video said it was easy to do and I think it said it would take 15 min. My neighbor had it fixed in 10 min. I could not be happier. Thanks Part Select and my neighbor Mike.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Followed the awesome Youtube video posted by PartSelect! Gave me the confidence to do it, and I'm glad I did. Thanks everyone at PartSelect!

Removed the screw from the old tray. Attached the new tray and return the screw using a wrench to assure the screw was torqued properly.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Fridge side: Remove all door bins. Close the door. Pry off top hinge cap. Using 5/16" nut driver, remove three screws. Remove top hinge by lifting it up. Place pad on floor to prevent marring. Hold door at sides. Open door halfway and lift it up and off the bottom hinge. Do not let door fall! Set door on pad. The lower and upper cams are different; do not mix them up (check the parts list). Remove the old lower cam from the hinge (on fridge) and install new lower cam with new screw. Remove the old upper cam from the bottom of door and install new one with shoulder screw provided. If the old cam does not have the shim, do not use the shim from kit. The kit has extra parts and screws. Lift up the door and set it on the lower hinge pin and close it. Reinstall the upper hinge and shim loosely with the three screws. Adjust the door before tightening the screws. Check that the gasket is compressed evenly all around. Open and close the door. The door should close easily. If the door does not close easily, remove it again and smear some Vaseline on the lower hinge pin and cam. Replace the door and put a little Vaseline on the upper hinge pin before inserting it into the door. Finally, replace the upper hinge cap and replace the door bins. Repeat procedure for freezer side. This fridge does not have water/ice dispenser in the door.

I took the upper three screws pull the door up and then removed the broker part in the bottom of door by removing one screw. Install new part and put door back securing it by the three screws on the top of regrigerator. Very easy

Googled for a solution to how to fix a refrigerator door that would not close. Was directed to a video from PartSelect. Was wrong brand, but I got the general idea. Then, I looked up a refrigerator repair for Whirlpool. Called PartSelect with my model number and ordered a Cam Kit. Total cost shipped $20. Arrived in two days during the Holidays! Nice! (Ordered 12/23, Arrived 12/26). Opened package, fired the video up. Fixed in 15 minutes. Amazing!

I have a KitchenAid side-by-side refrigerator and the right door clunked everytime it opened. We think it was damaged when contractors had to move the fridge and probably were too rough with it. I went on line and found that I could actually repair it myself (thanks to this web site, a great web site, by the way). I researched and found out through others that I needed a new door closing CAM kit. I only needed to fix 1 door, but bought the whole kit anyway (PS358690, Door Closing Cam Kit)to have spares. The kit showed up, I followed the great instructions via the video to remove the door, replaced the upper CAM on the door first and then ran into a snafu with the lower cam. The hinge on my model fridge does not have a replaceable CAM, it is physically attached to the door hinge. The instructions that came with the kit showed a hinge that was not my hinge - sigh. I had to put back all the old clunky parts, put the door back on and go order a new hinge (hopefully). Luckily there was a hinge available for my model with the CAM installed. I purchased it (PS331817, Door Hinge with Cam) and it came quickly like the other parts. I took the door off again (I knew how to do it this time), I replaced the hinge with ease, put the door back on and it is no CLUNK-FREE - Smooth like when we bought it. Thanks to everyone who wrote in about their clunking issues and thanks to PartSelect for the parts and the help.

I watched the video and then ordered the parts. My job was a little easier because the door was already tapped for a 10-32 bolt. Total time including set and tear down was less than an hour. Watching the video first made the job very simple.

(1)Remove all items stored in the inner door. (2)Remove all the shelves from the inner door. (3) Remove the top hinge cover screw and remove rhe hinge cover. (4) Remove the upper hinge (5) lift the door out of the lower hinge bracket and lay flat on a table or counter top. (6) Swap out the old parts with the new parts. (6) reassemble.

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

Emptied the inside door. Took out the screws from the top hinge. Lifted the door off the bottom hinge. Laid the door on the kitchen table. Replaced the cam on the door. Replaced the cam on the bottom hinge. Placed door back on bottom hinge and put screws back on top.