1985818201 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- HELMUT from MIDDLE VILLAGE, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Farmington Hills, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not work, broiler and range did work.
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mitch from brooklyn park, MN
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven didnt light
i removed old part, then installed new one. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Petersham, MA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
very slow cold water inflow
1. Identify washer model and symptom
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed
Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed
Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dixfield, ME
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Hose hookup was cracked.
My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Corpus Christi, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
slowly filled with water
The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Laguna Beach, CA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water inflow very slow and noisy
Great service! Part arrived within two days; installation instructions very
clear; washer back in service after15 minute installation. Thanks!
clear; washer back in service after15 minute installation. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Elburn, IL
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water going through water valve squealing/noisy
Disconnected the hot/cold water hoses. Removed screw that holds water valve in place. Removed two screws that hold valve to metal plate. Disconnected wire terminals from old valve and installed on new valve on the same spades. Disconnected water discharge line by loosing screw that hold line on valve, reattach to new valve. Removed old valve from plate, installed new one with the two screws to plate, then put in place and put in screw that hold valve in back of washer. Connected hot/cold hoses and fired it up and noisy water eliminated. About 30 minutes and back in service which made the wife happy that her washer was quite again. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Marion, IL
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
very little hot water incoming
Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Bethel Park, PA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water would not shut-off at initial filling of tub, hence washing cycle would not start. (This condition could have gone on for days as the water exited the wash machine as fast as it entered.)
Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!
Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,
Greg W.
inside face of machine. Replaced water valve, & restarted machine. Like new again!
Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,
Greg W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Edina, MN
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
washing machine would not operate on cold water setting
Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical wires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from Ann Arbor, MI
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The part that control water into tank was dripping
First, I opened up the back of the machine to see the way the water got into the tub. I turned off the water at the pipes, unplugged the machine, and disconnected the hoses from back. There were no leaks with the hoses, so I looked at the part that managed the water flow when operating and went on line to find the part.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neville from Lithonia, GA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would not Light
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Mayville, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ignitor would heat enough to open gas vavle to lite oven
unplugged the oven, unplugged the ignitor and removed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Girdwood, AK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this instruction helpful to you?
Thank you for voting!