1068275580 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ramona, CA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
refrig door was clunking when opening &closing.
rem upper hinge on door on & lifted door off. installed kit provided & ressemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Englewood, CO
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge door wouldn't close by itself
I removed the door (three screws on top). Flipped the door upside down, removed the cams, and replaced with the new ones and replaced the door. Now the door closes great. The only problem is that the door sort of "clunks" into place when I open or close it. I am not sure that I used the right cams. The drawing on the directions was not at all clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ft. Myers Beach, FL
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
cams on lower hinge fractured and door wouln't close
1. Used fine tip marker pen to draw outline of upper hinge position
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Harrisonburg, VA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Popping noise when opening and closing door.
The parts were delivered promptly. I ordered the kit assembly because I didn't know which part was the problem. Reading the remarks from other people's symptoms and solutions made the process much easier. I replaced both the upper and lower cams. Lubricated the cams and reinstalled the door.. Problem solved!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Prairieville, LA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door would not swing shut on its own as normal.
Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Salt Lake City, UT
- Parts Used:
- 4318165
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broken bottom door hinge, clunked when opened
I am a single female so the hardest part was lifting the door off and then trying to get it back on the hinge. I used the same bolts that were on the door so putting the new parts on was the easiest part. The slowest part was finding the right socket for the bolts and unscrewing the originals. Beats hiring a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard H from Mason City, IA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Teflon lower cam broke into from wear
removed door,removed worn part and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Amherst, NH
- Parts Used:
- 4318165
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Doors not closing without a serious push.
Replaced the refrigerator and removed doors to put the old unit in the basement as an overflow fridge. Noticed the cams broken/worn/missing on bottom door hinges. Ordered parts. When parts arrived, installed them and fridge back in operation. Parts kit had screws with slightly different sized heads, and if you used the wrong ones to mount the cams, there would be a clearance problem. There were no instructions with the parts to explain this. There also were a couple of plastic parts in the kit that were not used - no explanation given.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Lake Havasu City, AZ
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
door won't close its self or tight
Very easy to remove door replace door cams reassemble shuts tight now and works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Cordova, TN
- Parts Used:
- 2188436A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Old seal was no longer sealing
New freezer being delivered Monday
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Old Bridge, NJ
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door Closing Cam Broke
Part-fect!!!
Was this instruction helpful to you?
Thank you for voting!