25321082101 Kenmore Freezer - Instructions

My issue was water leaking from the door. I thought it was the gasket, so I removed the gasket and the entire panel off of the door. There was water behind it that had soaked the cardboard seal, so I left that front part off for over a week to let it dry. We determined between us and our two toddlers that perhaps the door hadn't been properly closed enough on a number of occasions, so before I bought a $100 gasket, I'd try making sure the door was shut with tape, turning the freezer on and seeing what happened. There was no water after a few days, so on another user's suggestion I purchased the $15 key and twist tied it to the freezer door. Now I am locking the door after use so we won't have leaking water any longer.

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws

I originally ordered an aftermarket replacement seal off intranet at half the price. It came in poor packaging & crumpled in a ball when received. After install, it would not seal & worse than the old seal that was replaced. I removed poor quality seal & returned it. I then ordered the OEM seal from PartSelect. It came in proper packaging. I kept the inside door shelving in place with two mid screws. Beginning at top I inserted sealing grove into channel of shelving working all the way around door frame. Making sure there was no crinkles or bulges at one place & it was all even. I replaced all screws ensuring not to over tighten. Close door and made sure magnetic seal pull closed to freezer & door on both sides by sliding my finger all the way around. I did not open the door for 1 hour to ensure rubber seal had taken proper shape to freezer frame. After I worked door Open/Close many times. Door seal worked perfectly every time then and now. This is a perfect example why to buy quality parts the first time.

Parts Select included a video, and I watched a couple more that were on YouTube. Watch the video and do the repair . . . it's very easy took me about 35 min once I got the freezer emptied, including cleaning the freezer. I used a Philips head screw driver and I think it was a 5/16 nut driver . . . you can do this. Freezer running fine, no noise. One thing I would be careful on is removing the back plate that covers the fan and motor, the edges can be sharp and you could cut yourself removing the back plate. Also don't try to put the rubber gasket in before you replace the back plate, install the back plate and the rubber gasket goes in easy peasy :)

I order another one thanks

took door of removed gasket replaced

Took longer to take out the shelves and the 10 screws holding the cover on then to replace the fan.
Local parts supply told me it would take two weeks to get the fan mator,ordered it from parts select and had in a couple days.

Needed a Phillips head screwdriver to remove bottom plate (kick panel). UNPLUGGED FREEZER. Removed plate pulled switch out through the mounting hole and unhooked the two electric wires. Placed wires on new switch, pushed wires back through the hole and seated the switch. Plugged in the freezer and opened the door - magic, the light came on. Replaced the front kick panel (hardest part was to line up the plate holes with the holes in the mounting bracket).

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

I removed the screws and replace the broken slide with the new slide. Put the basket drawer back on the track and it now stays in place and can easily be used once again.