79571309010 Kenmore Freezer - Instructions

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.

Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

IMPORTANT: REPAIR EASIER WITH ASSISTANT! Pull frig from kitchen cabinets & unplug. Remove food from freezer & frig doors. Have assistant hold freezer door closed against freezer. Remove hinge cap from top of freezer along with hardware using socket wrench. Carefully lift freezer door from hardware that joins the bottom of the freezer door to the top of the frig door. Rest freezer door upright off to the side. Have assistant open frig door & SUPPORT BOTTOM. Remove hardware from top of frig using crescent wrench & screwdriver. Carefully lift frig door off joint & lay on side to gain access to hardware on bottom. Remove hardware using a screwdriver & replace worn nylon bushing. Reverse disassembly steps. Remove frig & freezer door shelves & clean inside. Clean outside frig, especially the back vents. Clean the floor where frig lives & push back into place. Enjoy clean SELF-CLOSING, NON-GRINDING frig door!

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

slid screw driver under edge of switch, easy.

I removed the cover from the rear of the unit, with a screwdriver. Then with a adjustable wrench unscrewed the top nut of the water valve.I then removed the screw holding the valve to the wall of the fridge. Turned the valve upside down and removed the line going up to the ice maker. No tools needed here as it is a quick connect fitting.Use reverse order to install valve.I am 65 years old and if I can do this anyone can. Good luck from TX.

easy, a screw driver repaired in a mintue

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

replaced the ice maker with the new assembly kit, the longest time taken was to fit back the pull out door .. had to align the slots correctly and check that it slid back and forth easily.

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.