25326442100 Kenmore Freezer - Instructions

Replaced freezer defrost thermostat. Unit worked perfectly.

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

replaced control board and installed surge protector

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.

I paid about $50 for a tech to come to the house to troubleshoot the freezer. He id'd the temp control unit in about 30 minutes and told me he could repair the freezer for an additional $300 or so. I told him 'no'. I looked up the part number with partselect and ordered the temp control unit for about $40 including shipping. I simply plugged in the unit and reset the rear compartment panel and gaskets. I plugged the unit in. The freezer ran but did not freeze. I inspected the rear of the freezer and found that the tech had left the compressor unplugged. I connected the compressor and turned the freezer on, It is working just fine.

Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.

I followed the You-Tube instructions, removed the ice from the compressor and replaced the thermostat with the part I received from Part Select. What I took out was a part that was very much inferior to the replacement part. The repair saved me a lot of money for a new freezer and it was not difficult to do following the video. Now the freezer runs better and quieter than ever. Thank you Parts Select.

Replace thermostat and show and tell made it easy.

Replaced fan. I ordered the fan and received it the following.(-:

The evaporator fan would make a very high-pitched whine/squealing noise usually after starting up after a defrost cycle, although, it would make the same noises during normal operation. After performing a thorough inspection of the fan blade and motor, I discovered that there was no interference to the rotating fan, and realized the motor must be failing. After removing the food and racks from the main body of the freezer, I had to remove 8 Philips-tipped screws that held the inside back panel cover on. I disconnected the fan motor from the main wiring harness, removed the fan mounting bracket (2 5/16" hex head screws), and then removed the fan motor from the mounting bracket (2 5/16" hex head bolts. I removed the fan blade and conducted a visual inspection, and found not blemishes of broken/damaged pieces. I mounted the new motor and used the existing fan blade, and replaced everything in the reverse order. I turned on the freezer and it has been operating perfectly since. I disassembled the old motor and discovered that the stator coils were worn, and the bearings allowed to much forward/aft motion.

Unplug freezer let stand all night to defrost. Remove the tray cover which is located on the upper back area inside the freezer.( 3 twist fittings remove it ). Remove the upper stainless steel panel which is secured with 6 screws. This will drop down exposing the condenser. Note all the wires and fan will stay attached to the stainless steel panel, this panel will drop down no need to unplug anything. On the left upper side next to the condenser you will see the thermostat. Two color coded wires. Remove the thermostat and install the new one at the same location.

Found voltage coming into unit but not making it through the control unit. Thermo switch could easly be bypassed with no results so only thing left was the control mod. It was worth the $51.00 guess , ordered the part with credit card about noon, the next day Fed Ex came to the door about 2 PM the freezer was running by 2:30. Very impressed by everyone envolved. Spent the rest of the day bragging about my repair ability. Felt good to hear that baby fire up. Thanks again

inserted key and turned