79571302011 Kenmore Freezer - Instructions

Replaced the glide.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

IMPORTANT: REPAIR EASIER WITH ASSISTANT! Pull frig from kitchen cabinets & unplug. Remove food from freezer & frig doors. Have assistant hold freezer door closed against freezer. Remove hinge cap from top of freezer along with hardware using socket wrench. Carefully lift freezer door from hardware that joins the bottom of the freezer door to the top of the frig door. Rest freezer door upright off to the side. Have assistant open frig door & SUPPORT BOTTOM. Remove hardware from top of frig using crescent wrench & screwdriver. Carefully lift frig door off joint & lay on side to gain access to hardware on bottom. Remove hardware using a screwdriver & replace worn nylon bushing. Reverse disassembly steps. Remove frig & freezer door shelves & clean inside. Clean outside frig, especially the back vents. Clean the floor where frig lives & push back into place. Enjoy clean SELF-CLOSING, NON-GRINDING frig door!

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

slid screw driver under edge of switch, easy.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

easy, a screw driver repaired in a mintue

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

replaced the ice maker with the new assembly kit, the longest time taken was to fit back the pull out door .. had to align the slots correctly and check that it slid back and forth easily.

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

Caution removing plastic molding with putty knife or flat bar . Roll the gasket toward the inside of frig ,push old holder up carefully out of gasket. Half way out tilt holder back to avoid ceiling . Save old holder for template ,remove screw from bottom,push out rod ,caution clip is spring loaded, install in new holder in reverse,slide back into gasket(carefully)!!replace molding

I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.