25326468101 Kenmore Freezer - Instructions

just like the video show sa 1,2,3 yeaaa thanks

Took out three shelves. Removed 9 screws with a battery powered drill with a phillip screwdriver bit. Popped off the thermostat like I had seen on the video. Put the new thermostat on. Replaced the two wires one at a time. Reassembled the unit. This was so quick that my wife told me to let her know when I wanted to fix the freezer. She was shocked that I had completed the job. I'd been in the garage less than 10 minutes. It has been six weeks. and the freezer is working perfectly.

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

Replaced freezer defrost thermostat. Unit worked perfectly.

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

I paid about $50 for a tech to come to the house to troubleshoot the freezer. He id'd the temp control unit in about 30 minutes and told me he could repair the freezer for an additional $300 or so. I told him 'no'. I looked up the part number with partselect and ordered the temp control unit for about $40 including shipping. I simply plugged in the unit and reset the rear compartment panel and gaskets. I plugged the unit in. The freezer ran but did not freeze. I inspected the rear of the freezer and found that the tech had left the compressor unplugged. I connected the compressor and turned the freezer on, It is working just fine.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

replaced control board and installed surge protector

I followed the You-Tube instructions, removed the ice from the compressor and replaced the thermostat with the part I received from Part Select. What I took out was a part that was very much inferior to the replacement part. The repair saved me a lot of money for a new freezer and it was not difficult to do following the video. Now the freezer runs better and quieter than ever. Thank you Parts Select.

Replace thermostat and show and tell made it easy.

The evaporator fan would make a very high-pitched whine/squealing noise usually after starting up after a defrost cycle, although, it would make the same noises during normal operation. After performing a thorough inspection of the fan blade and motor, I discovered that there was no interference to the rotating fan, and realized the motor must be failing. After removing the food and racks from the main body of the freezer, I had to remove 8 Philips-tipped screws that held the inside back panel cover on. I disconnected the fan motor from the main wiring harness, removed the fan mounting bracket (2 5/16" hex head screws), and then removed the fan motor from the mounting bracket (2 5/16" hex head bolts. I removed the fan blade and conducted a visual inspection, and found not blemishes of broken/damaged pieces. I mounted the new motor and used the existing fan blade, and replaced everything in the reverse order. I turned on the freezer and it has been operating perfectly since. I disassembled the old motor and discovered that the stator coils were worn, and the bearings allowed to much forward/aft motion.

Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.

Replaced fan. I ordered the fan and received it the following.(-:

Watched video on Part Select which shows you how to replace the thermostat with several good pointers. Very easily done and now the freezer works great.

Ordered freezer key friday afternoon received it saturday afternoon. Fast service