79578354800 Kenmore Freezer - Instructions

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

IMPORTANT: REPAIR EASIER WITH ASSISTANT! Pull frig from kitchen cabinets & unplug. Remove food from freezer & frig doors. Have assistant hold freezer door closed against freezer. Remove hinge cap from top of freezer along with hardware using socket wrench. Carefully lift freezer door from hardware that joins the bottom of the freezer door to the top of the frig door. Rest freezer door upright off to the side. Have assistant open frig door & SUPPORT BOTTOM. Remove hardware from top of frig using crescent wrench & screwdriver. Carefully lift frig door off joint & lay on side to gain access to hardware on bottom. Remove hardware using a screwdriver & replace worn nylon bushing. Reverse disassembly steps. Remove frig & freezer door shelves & clean inside. Clean outside frig, especially the back vents. Clean the floor where frig lives & push back into place. Enjoy clean SELF-CLOSING, NON-GRINDING frig door!

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

slid screw driver under edge of switch, easy.

I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

When the shelf was delivered, all we had to do was open the door of the fridg. and put the glass into place. pretty easy, huh?

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Gasket held in place by plastic bezel. Remove bezel by carefully pulling it toward you. Held in place by plastic clips. May need to pry carefully near clips. Pull gasket away from front edge of door. Gasket holder held by plastic swivel pieces top and bottom. Snap these out. Slide the gasket holder off the gasket. Remove the screws and slip the metal rod out of the broken holder. Retain screws, plastic clips, and cam. Slide the rod into new holder adding plastic clips and cam. Replace screws. Slide holder back onto gasket. Snap plastic clips into slots, being careful to bend the springs back so they go into the channel. Replace bezel. See videos on replacing door gaskets.

Caution removing plastic molding with putty knife or flat bar . Roll the gasket toward the inside of frig ,push old holder up carefully out of gasket. Half way out tilt holder back to avoid ceiling . Save old holder for template ,remove screw from bottom,push out rod ,caution clip is spring loaded, install in new holder in reverse,slide back into gasket(carefully)!!replace molding

This was late on a Sunday afternoon. I immediately called the store where I purchased the refrigerator who told me to go on-line for any parts. So I went to PartSelect and was able to find the correct part very easily and then order it. It arrived on Thursday without having paid for any upgrade in shipping time.I am very impressed with this company.

looked up on google for lg refridgerator replacement parts, found parts select, went to their web site and found the exploded view of my refridgerator called them and ordered the parts necessary. they shipped them very fast and have great cusomer service. I will use them again if i need a part for an apliance.