79571026011 Kenmore Freezer - Instructions

remove all trays from refrigerator , remove screw holding rail and install new rail.

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

removed old handle

Installed new handle with hex wrench used to tighten up

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!

Removed back panel and water inlet valve and replaced with a new water inlet valve

1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.

( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks

The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Go to this site on You Tube to watch the "how to" replace the gasket retainer. The retainer I needed did not come with brackets or the cam you will need. You will need transfer them from the old retainer to the new one. Not hard, just be mindful of position of the items you remove to put them back in place the same way. A metal rod holds the brackets and spring in place with a screw on one end to prevent rod from sliding off retainer. The cam has a screw that holds it in place, use from old retainer. If the old cam is not broken use the one from the old retainer. It is not hard and you will save $$$ that you would pay an appliance repair company.

Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.

I waited for 2 weeks for a professional appliance repairman to fix my water leak. He kept telling me he was trying to get the part. I finally gave up on him and ordered the part online. Only took a few minutes for the repair. Got the part via mail in 3 days.

Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.