1068251940 Kenmore Freezer - Instructions

Just loosened the screws at the top of the door hinge bracket, lifted the door off the hinge and set down on its side. Removed the broken cams, both the door cam & Cam on the lower hinge. Discarded the old parts after making sure the new parts would match up with the holes and screw holes would align. Installed a new cam on both lower hinge bracket and bottom of the door with new screws provided. Added some lubricant to minimize future wear and tear and re-installed the screws. Lifted the door back onto the lower hinge pin, Lifted up the pin on the top of door bracket until the pin would slid into the hole on top of door. Tightened the screws on top of the door hinge bracket. checked to make sure door sealed tightly around the perimeter of door opening and we were done. Total time was about 15-20 min. Anyone could do it. Thanks for the instructions and parts. Very pleased with the results. Sincerely, Jim

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

(1)Remove all items stored in the inner door. (2)Remove all the shelves from the inner door. (3) Remove the top hinge cover screw and remove rhe hinge cover. (4) Remove the upper hinge (5) lift the door out of the lower hinge bracket and lay flat on a table or counter top. (6) Swap out the old parts with the new parts. (6) reassemble.

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

Emptied the inside door. Took out the screws from the top hinge. Lifted the door off the bottom hinge. Laid the door on the kitchen table. Replaced the cam on the door. Replaced the cam on the bottom hinge. Placed door back on bottom hinge and put screws back on top.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Viewed the viedo - it showed what to do

I watched the video and then ordered the parts. My job was a little easier because the door was already tapped for a 10-32 bolt. Total time including set and tear down was less than an hour. Watching the video first made the job very simple.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

Took out the door bins, 1 bolt on the plastic cap, 3 bolts on the hinge, took the door off, replaced cam at the bottom, all same size bolts, reset the door spent longer time cleaning the door selfs all done by my self in less than 30 min. others said it helped to have second pair of hands "my wife would of just got in the way :)"

Very easy!