25328262800 Kenmore Freezer - Instructions

On 08/13 / 2025 starting in the AM --- My Wife Marie Defrosted -- Cleaned and dried the Kenmore up right freezer she has had for more than 33 years --- She noticed there was screws behind the inside door gasket and informed yours truly --- 1st Jacques loosened all the screws then removed the old gasket -- took it cleaned it and boxed it in the box the new gasket came in --- Took new freezer door gasket and installed it neatly around the door by tucking back part of door gasket between door panel and door --- once all was in place started tightening all screws starting at bottom holding bottom gasket material tight with other hand --- then working counter clock wise till done !!! there you go it was very easy and turned out great !!! Now everything is like new !!! Jacques And Marie / from Virginia

The timer in this older unit is clearly exposed at the back of the freezer underneath the freezer compartment. It is attached with two Phillips head screws. After the screws are removed, the timer can be unplugged and the new one plugged in. The new timer has an extra flange to allow it to be used on more than one model of freezer. In order to mount the timer in this unit, you have to remove the extra flange by carefully cutting it away from the timer body, in similar fashion to what's depicted in the online video. This will allow you to mount the new timer to the mounting plate using the two screws from the old timer.

First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.

Loosen screws, removed old gasket seal, replace with new gasket (nice to use 2 sets of hands) and re screwed. Used hairdryer to heat up and fluff out a spot that wasnt seal all the way. Pretty simplementation to do.

removed the screws/nuts; pulled the back panel off, removed the old thermostat (wires just popped apart) replaced the new thermostat (wires just popped back on) replaced the back panel and the nuts and TaDa!!

I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.

Works great!!!

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

Unscrew all the fasteners from the door inner cover from the bottom to top to hold it in position, got rid of the old gasket.

I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.

this is a one man job but with two will be easer

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

Took about an hour previously to deice freezer, timer was running,drain was open, jumped defrost thermostat out and heater was O.K. Defrost thermostat was just a plug and play item, the time involved was in taking the freezer apart to get to it.

First of all thanks to all who posted their stories, because those stories helped me to narrow down what could have gone wrong with my fridge. I did not know how frost-free refrigerators worked at all, reading your stories and doing some on_line research I understood the theory behind the work. My freezer was working constantly, but fridge was warm, cold air would not reach to fridge because freezer was completely frosted.
I had ordered defrost heater, defrost timer and thermostat. I was sure one of these parts was the problem.
First I used flat screwdriver to turn the timer manually untill frdge stopped running(timer is on the left bottom corner behind the black decoratve plastic under the door) . Waited about 20-30 min, checked ,freezer was still frosted. I disconnected the fridge from the wall socket and took shelves out from freezer compartment. This is where hair-dryer came in handy or you could wait till ice would melt on its own, which could take long time.Then loosend 2 screws on left wall that were holding icemaker unit half-way , unplugged the icemaker and took it out. Then took the light-bulb and cover off. Next I unscrewed and took the posts out that were holding shelves in place. Then I took remaining screws from back wall out and gently pulled back cover up then forward a little until I could see electrical connectors behind the cover and unpluged them. Back wall cover was ready to come out. I discovered thick wall of ice covering entire cooling unit. Used handy hair dryer again. When the ice melted, I saw the thermostat was busted open ( Iguess water or moisture got into the unit, then froze and ice pop-openned the cover damaging one of the connecting wires). I diconnected wires and changed the thermostat , which was very easy, just one clip holding it in place . Then plugged the fridge and checked if heating unit was working by touching it. Negative. Closed the door and let fridge run for 15 min, turn timer with screwdriver until fridge stopped working, cheked heater again- wallah it was warm and then it got really HOT! and melted all of the new frost build-up(a sign that thermostat was working). Closed the door waited another 15-20 min, fridge came-on on its own. Unplugged the fridge, pulled it forward from the wall and used sponge to drain the water from holding tray- about one half gallon of it. This is a good time to use a vacuum clener to undust the back and under the fridge. Then put everything back, in reverse order, ofcourse. Cleaned fridge and freezer compartments with warm soap and winneger solution (really good- this was a present to my wife who took our two little daughters to grandmmas and out of my way), put everything back and turned the fridge on recommended settings. Its been 5 days allready and it works great ( I used thermometr to check temperature inside the fridge and freezer). I'm thinking of returning defrost heater and timer back.Thanks PartSelect.Com, I saved lots of money. Hope this story will be helpfull to someone.Thanks for your time!

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .