25326072103 Kenmore Freezer - Instructions

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

My issue was water leaking from the door. I thought it was the gasket, so I removed the gasket and the entire panel off of the door. There was water behind it that had soaked the cardboard seal, so I left that front part off for over a week to let it dry. We determined between us and our two toddlers that perhaps the door hadn't been properly closed enough on a number of occasions, so before I bought a $100 gasket, I'd try making sure the door was shut with tape, turning the freezer on and seeing what happened. There was no water after a few days, so on another user's suggestion I purchased the $15 key and twist tied it to the freezer door. Now I am locking the door after use so we won't have leaking water any longer.

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.

I removed the shelves, unscrewed the cover panel of the fan motor and regulator dial, disconnected the fan motor from power, unscrewed 2 screws holding the motor to the mounting bracket and put the new motor in it's place. New motor had no thread in the mounting holes, so I put new tread in so I could use the 2 screws. Another option would have been to drill all the way through the mounting holes and use longer screws or bolts. Of course I turned the power off before I started repairs. Freezer runs like new now. Technicians wanted $400 for the job, while it cost me a mere $55 for the Motor.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws

I originally ordered an aftermarket replacement seal off intranet at half the price. It came in poor packaging & crumpled in a ball when received. After install, it would not seal & worse than the old seal that was replaced. I removed poor quality seal & returned it. I then ordered the OEM seal from PartSelect. It came in proper packaging. I kept the inside door shelving in place with two mid screws. Beginning at top I inserted sealing grove into channel of shelving working all the way around door frame. Making sure there was no crinkles or bulges at one place & it was all even. I replaced all screws ensuring not to over tighten. Close door and made sure magnetic seal pull closed to freezer & door on both sides by sliding my finger all the way around. I did not open the door for 1 hour to ensure rubber seal had taken proper shape to freezer frame. After I worked door Open/Close many times. Door seal worked perfectly every time then and now. This is a perfect example why to buy quality parts the first time.

The replacement of the Thermistor is a snap. Take out the bottom two shelves, remove the 8 screws in the back panel, pull it out. Cut the wires to the old thermistor and install the new one. There are demo's on you tube so I wont go into detail.

Unfortunately the replacement door seal was packaged with twists in it and would not lay flat on the door. I found the old seal was not the problem - but instead ice had grown between the door and the door panel so that the door would not seal properly. I reinstalled the old door seal and everything is fine now.

I order another one thanks

took door of removed gasket replaced

Needed a Phillips head screwdriver to remove bottom plate (kick panel). UNPLUGGED FREEZER. Removed plate pulled switch out through the mounting hole and unhooked the two electric wires. Placed wires on new switch, pushed wires back through the hole and seated the switch. Plugged in the freezer and opened the door - magic, the light came on. Replaced the front kick panel (hardest part was to line up the plate holes with the holes in the mounting bracket).

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.