Models > 79577563600 > Instructions

79577563600 Kenmore Freezer - Instructions

Jump to:

All Instructions for the 79577563600
46 - 60 of 111
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Calvin from Northome, MN
Parts Used:
6600JB1010A
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from TONAWANDA, NY
Parts Used:
6600JB1010A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from CHATTANOOGA, TN
Parts Used:
5075JA1044E
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
the ice bin was extremely easy to set in....no explanation necessary however, The customer service left a lot to be desired!
The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sidney from ENDICOTT, NY
Parts Used:
6600JB1010A
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from FALL RIVER, MA
Parts Used:
4620JJ2009A
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JON from OJAI, CA
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from HOULTON, ME
Parts Used:
6600JB3007A
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Interior light switch not working
Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Greg from CASA GRANDE, AZ
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from CURWENSVILLE, PA
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dean from HILLSDALE, MI
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from PENNSVILLE, NJ
Parts Used:
6600JB1010A
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from DICKINSON, TX
Parts Used:
MDS38201426
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Ashland, MA
Parts Used:
6600JB1010A
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from STEPHENVILLE, TX
Parts Used:
EBS61443363
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken freezer rail.
Took out tray , removed 2 screws, removed old rail and installed new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from BETHPAGE, NY
Parts Used:
AJU72992601
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79577563600
46 - 60 of 111