79571022010 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bard from Alpine, CA
- Parts Used:
- AAP33726606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem
It's a snap in part. 10 seconds to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Elk Grove, CA
- Parts Used:
- 4932JA3002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald A. Green from Pelham, AL
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door latch/ cam shaft broke on left side door
Removed white plastic trim and installed new latch / cam shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mashpee, MA
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken
removed 1 screw and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Wimberley, TX
- Parts Used:
- 5231JA2006F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The water filter needed to be replaced.
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Murrieta, CA
- Parts Used:
- EAV43060808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
only 2 of many led lights working
Unscrewed cover, 2 screws. Had some trouble getting it out. Was concerned about damaging the cover and cracking the plastic. Was able to remove it with no damage but it comes out of the installation slots very hard. Be patient and wiggle it until it comes out. Two more screws release the led board. It was changed very easily. Reassembly was easy but had to fight the plastic cover to get it to snap into place. Tightened the two screws for the cover. Broke the cover where the flat of one of the screws tightens against. I ordered other parts which assembled well. One part came in incorrect which I was reimbursed for and the new part was sent right out. Over all I give Parts Select a A ratin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Carson, CA
- Parts Used:
- 4987JJ2002P, 4987JJ2002N
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The gasket on both top doors were torn
I first took off a plastic trip strip which just popped off with a little pull. Then I pulled the gasket off slowly all around the perimeter of the door and snapped off the guide strip with the help of a screwdriver. I installed the gasket next first the guide strip then followed up with the pushing the gasket into the groove all around the door. Did the same procedure on the other door. The gaskets came very well packed and undamaged. It took approximately 2 weeks because one gasket was on back order. Thank you for your help with these parts. It would have cost me 3 times as much if the repairman performed this repair.
Was this instruction helpful to you?
Thank you for voting!