25344733110 Kenmore Freezer - Instructions

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

Instructions were very good. Easy to do. Need to put in instructions, that you will NOT hear anything until about 8 hours later. Just because it is plugged in, water on...no sounds until 8 hrs later, and will hear the water doing into the ice maker.

Replaced fan. I ordered the fan and received it the following.(-:

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

Removed three screws each side to remove old slides. Needed spacers under new slide so that drawer would stay on track. Cut old slide to make spacers and installed both slides in 15 mins.

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

My husband has never done this type of work and he found it very easy to read the instructions and follow the step by step process. Our only concern is that it should tell you before you begin that it takes 24 hours to produce ice, we thought we had a problem until we read further on into the instructions to find that out.

new house double wide came with refrigerate but no icemaker. The kit didnot come with water valve tap for water suply line that kit only cost 10$ at hareware store if i kown I needed it. I would have order it the same time. I did get everything in add on icemaker kit I forgot about water suply. very easy instull and my order came very fast thank you

Spent most of the time reading and understanding the instructions. The installation went ok. Relatively easy.

Installed new fill valve in less than 30 minutes and waited for 24-8 hours for results to no avail. Ice maker mechanism was shot and still would not work. Went to Lowes and bought entire ice maker add on kit for my model ice box and installed in 30 minutes and have been making ice ever since. Your 99% cure rate was 100% incorrect. Save the time and effort and go to a big box store and just get a new ice maker. By the way, it only costs about $20 more to do that.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.