79572022110 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from locust valley, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Awilda from Staten Island, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The water line was leaking
Removed the damaged tube and replaced the it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Orlando, FL
- Parts Used:
- MJX41178908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Pump for ice maker leaked.
Easy repair. Unplugged refer. Took back cover off with screwdriver. Unscrewed the support for the pump. Unhooked water lines from both ends of bad pump. Pulled electrical line off the old pump. Put the support on the new pump, hooked up lines, and electrical plug and screwed the pump to the frame. Put the coever back on unit. Plugged back into wall. Worked immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toai from Monroe, WA
- Parts Used:
- 6421JB2002R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice maker door stay open. And not close back.
So easy that my 13 years old son replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorothy from SALISBURY, MD
- Parts Used:
- MJB63190001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from ROGERS, MN
- Parts Used:
- 6600JB3001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mashpee, MA
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken
removed 1 screw and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald A. Green from Pelham, AL
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door latch/ cam shaft broke on left side door
Removed white plastic trim and installed new latch / cam shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Elk Grove, CA
- Parts Used:
- 4932JA3002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Carson, CA
- Parts Used:
- 4987JJ2002P, 4987JJ2002N
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The gasket on both top doors were torn
I first took off a plastic trip strip which just popped off with a little pull. Then I pulled the gasket off slowly all around the perimeter of the door and snapped off the guide strip with the help of a screwdriver. I installed the gasket next first the guide strip then followed up with the pushing the gasket into the groove all around the door. Did the same procedure on the other door. The gaskets came very well packed and undamaged. It took approximately 2 weeks because one gasket was on back order. Thank you for your help with these parts. It would have cost me 3 times as much if the repairman performed this repair.
Was this instruction helpful to you?
Thank you for voting!