79577559600 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alice from Wimberley, TX
- Parts Used:
- 5231JA2006F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The water filter needed to be replaced.
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Jose, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Unit kept beeping as if the freezer door was open
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from locust valley, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Awilda from Staten Island, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The water line was leaking
Removed the damaged tube and replaced the it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Port Angeles, WA
- Parts Used:
- 4838JA2002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Crack In Old Tank Assembly
Removed the old, replaced with new. . . That easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mashpee, MA
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken
removed 1 screw and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Pequannock, NJ
- Parts Used:
- 6600JB3007E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
interior lights stay on
Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Abilene, TX
- Parts Used:
- 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover and case had melted
I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Santa Fe, NM
- Parts Used:
- 3551JJ2021A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
replace piece
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Troutdale, OR
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the lights inside the frig weren't shutting off
the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G.J. from WHITE BIRD, ID
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights in upper refrigerator would not turn off with doors closed
replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Vero Beach, FL
- Parts Used:
- 6600JB3007E, 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights Stayed on Melted Light cover
Replaces door switches - removed screw from door hinge cover, lifted cover and removed switch. Plugged in new switch and reversed process. Removed screws from light bracket. Attached new frame to slots in roof and used screws to attach. Clipped on light cover.
Was this instruction helpful to you?
Thank you for voting!