1068254983 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Hobe Sound, FL
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
See below
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defective. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defective. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burton from Pecatonica, IL
- Parts Used:
- WPW10662129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Laramie, WY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ba from Van Nuys, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator stop cooling
I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph T. from Morgantown, WV
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bradley from harlingen, TX
- Parts Used:
- WP2262181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
stopped cooling
I looked for the obvious sign of malfunction, a leak lack of air flow dirty coil finding nothing obvious I checked the electrical components and the first was the start relay with a bimetal temperature switch was the problem that was identifyed when removed due to the relay sounding like it was internally damaged because of severe rateling
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katina from Cambridge, MA
- Parts Used:
- WP2262181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The fridge was blowing how air in the freezer and in the bottom of the fridge.
I was careful to unplug each cord one at a time so that I can easily match them up to the new start relay. Once I got the cords plugged into the new start relay, I went ahead and plugged in the fridge and it worked like it never stopped working. I must admit, I'm still nervous about this fridge because I never had to do anything like this in my life so in the back of my mind, I'm always wondering if I did it correctly or not. I was giving a lesson on how to make sure that I have it on correctly but that didn't put me at ease..lol. Parts Select sent this part in less then a day and that made me appreciate there business even more. I was concerned that the part wouldn't get here until later on that week.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene from Whitehall, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No light in frig
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from buchanan, TN
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator Would Freeze Up And The Food Section Could'nt Cool
I just followed the enclosed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIO from CHARLOTTE, NC
- Parts Used:
- WP2262181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
freeser and cooler they wasnt work and it won't start
First thing, I didn't have any idea how to fix my refrigerator, but I saw some videos on line, I just pull the start relay, it sound like little parts inside. I order to PART SELECT my Start Relay combination and part select have more comments, diagrams it was easy to find the part. Put the new start relay was easy, I just conect those wires back it took less than 10 minutes and it's working now.thanks to Part Select to make easy to fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Jefferson Township, PA
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Light
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Randolph, ME
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Frig not cooling.
After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Saratoga Springs, NY
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Refrigerator Door wont close
Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Beloit, WI
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light did not come on (bad bulb!) on TC18KL
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this instruction helpful to you?
Thank you for voting!