25323024103 Kenmore Freezer - Instructions

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Plugged in the new parts. No tools were required. Sears wanted to charge me $300 for the repair!

Not sure if it was the Controller or the run capacitor that went bad and took out the controller, so, purchased both an replaced both. Snapped of the wire retainer,unpluged the controller, used pliers and small screw driver to disconnect the controller, plugged wires into the new controller, plug the run capacitor into it ahd reinstalled, so far running great.

Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

Replaced fan. I ordered the fan and received it the following.(-:

I followed the You-Tube instructions, removed the ice from the compressor and replaced the thermostat with the part I received from Part Select. What I took out was a part that was very much inferior to the replacement part. The repair saved me a lot of money for a new freezer and it was not difficult to do following the video. Now the freezer runs better and quieter than ever. Thank you Parts Select.

The evaporator fan would make a very high-pitched whine/squealing noise usually after starting up after a defrost cycle, although, it would make the same noises during normal operation. After performing a thorough inspection of the fan blade and motor, I discovered that there was no interference to the rotating fan, and realized the motor must be failing. After removing the food and racks from the main body of the freezer, I had to remove 8 Philips-tipped screws that held the inside back panel cover on. I disconnected the fan motor from the main wiring harness, removed the fan mounting bracket (2 5/16" hex head screws), and then removed the fan motor from the mounting bracket (2 5/16" hex head bolts. I removed the fan blade and conducted a visual inspection, and found not blemishes of broken/damaged pieces. I mounted the new motor and used the existing fan blade, and replaced everything in the reverse order. I turned on the freezer and it has been operating perfectly since. I disassembled the old motor and discovered that the stator coils were worn, and the bearings allowed to much forward/aft motion.

Replaced freezer defrost thermostat. Unit worked perfectly.

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.