25321021103 Kenmore Freezer - Instructions

took the shelves out, unscrewed the rear panel,unpluged the thermistat and uncliped it from the line.Replaced with new thermistat in the reverse order. Before turning the unit back on,allowed the coils to defrost.All of the process was shown in your vidio that I was able to view while ordering the part. Thank you

Fist I removed the tow screws that hole the fan bracket - then remove the 2 screws that hole the fan-disconnect the wires and replace new unit.

Turned thermostat down and freezer began to run. Once it was at desired temp it shut down and did not start again. Turning the thermostat down again caused the freezer to start again. At this point, decided the thermostat was defective.Unplugged the freezer and removed the shelving. Removed the knob from the thermostat. Removed the nine screws that held the back panel in place and pulled the panel forward. Removed the assembly that held the sensing tube in place and removed the sensing tube from it. Depressed the thermostat latch which holds it in the back panel and separated it from the panel. Removed the electrical connections and removed the thermostat assembly from the freezer. Reinstalled the new thermostat in the reverse order.

Purchased new freezer.

Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Replaced defrost thermostat and defrost timer on my commercial Kelvinator freezer. Took out screws inside freezer compartment that hold panel at top inside freezer.Once the screws were removed I pulled out the thermostat dial so the panel was free to drop down and expose coils to the freezer that were located in the top rear of the inside freezer compartment.The defrost thermostat was located on the top of the coil to the top left as you face the inside of the Kelvinator KFS220RHY1 freezer. Very easy unplug old and plug in new defrost thermostat. Also replaced timer located in the back side of the freezer down near the middle of the bottom of the freezer near the compressor. There were two nuts holding the timer in the back of the freezer once I took those out I just unplugged the old timer and plugged the new timer in ....very simple fix. I have only run my freezer for a week since I replaced both parts but so far all is working well.

Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.

Layed the seal out in the driveway in the sun to warm it up. Unscrewed the screws, not all the way. Removed old seal. Stared at the top corner, working our way around, making sure corners lined up. Don't pull on the seal or you will stretch it. Once it's applied and all corners are lined up, tighten crews down lightly. The seal mediately stuck but it took a few hours for the vacuum to suck it down. Easy breezy!

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

I knew from a problem years ago that the Thermostat was the likely cause so I ordered a new part and replaced it. Only need a phillips head screwdriver to remove the part and add the new one..

I followed the video. It’s not that it’s a bit difficult, it’s just going slowly and carefully.
The thing that I didn’t allow the 24 hours for the gasket to relax after leaving the box. Also, I forgot to heat the gasket and put a small layer of Vaseline.
So the next day I noticed the the gasket wasn’t seating properly and went back to the video and carefully followed the steps to gently heat it with a hair dryer and Vaseline. The gentle heat let the gasket properly relax and seat. The Vaseline helped created a small vacuum to complete the gaskets “training” to seal properly.
24 hours later it was beautiful and the freezer was working like new.
Parts Select was great to deal with.

I replaced the timer and the defrost thermostat. The defrost thermostat replacement was almost exactly like the training video here. The old part attached slightly differently. The most time consuming part was thawing out the heat exchanger, which was completely covered with ice, inside and out.

Compared to the training video, the timer took more work given its location. It was low to the ground and a bit difficult to get at around the other wires and parts. However, the new part fit perfectly. I just unplugged and unscrewed the old part then reversed those steps with the new one.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

Removed the old defrost timer by removing 4 screws on the holding bracket. Disconnected the wire harness. Reconnected the wire harness to the new part. Installed the new part with 2 screws on the top of the molded bracket. I am a 67 year old woman... easy-peasy. (the defost timer is located in the bottom left rear of the freezer.