1068261340 Kenmore Freezer - Instructions

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

Emptied the inside door. Took out the screws from the top hinge. Lifted the door off the bottom hinge. Laid the door on the kitchen table. Replaced the cam on the door. Replaced the cam on the bottom hinge. Placed door back on bottom hinge and put screws back on top.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Viewed the viedo - it showed what to do

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Watched the video and viola, it was done. This was on the refrigerator side. Probably should have unplugged it, but didn't. One suggestion is hang a sheet in front to keep the cool in as best you can, even though it went really quickly.

Just loosened the screws at the top of the door hinge bracket, lifted the door off the hinge and set down on its side. Removed the broken cams, both the door cam & Cam on the lower hinge. Discarded the old parts after making sure the new parts would match up with the holes and screw holes would align. Installed a new cam on both lower hinge bracket and bottom of the door with new screws provided. Added some lubricant to minimize future wear and tear and re-installed the screws. Lifted the door back onto the lower hinge pin, Lifted up the pin on the top of door bracket until the pin would slid into the hole on top of door. Tightened the screws on top of the door hinge bracket. checked to make sure door sealed tightly around the perimeter of door opening and we were done. Total time was about 15-20 min. Anyone could do it. Thanks for the instructions and parts. Very pleased with the results. Sincerely, Jim

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

I found this part on PartSelect. I was so excited it also showed a video on how to fix the door. My neighbor said he would help me and I ordered the pkg. It took 3 days to get here since I ordered Friday night and the part arrived Tuesday , this was the Easter Sunday week end also. Well the video said it was easy to do and I think it said it would take 15 min. My neighbor had it fixed in 10 min. I could not be happier. Thanks Part Select and my neighbor Mike.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.