25323425100 Kenmore Freezer - Instructions

Removed the old defrost timer by removing 4 screws on the holding bracket. Disconnected the wire harness. Reconnected the wire harness to the new part. Installed the new part with 2 screws on the top of the molded bracket. I am a 67 year old woman... easy-peasy. (the defost timer is located in the bottom left rear of the freezer.

Bought the defrost timer based on PartSelect recommendations, installed it and no change. Apparently the old one was fine but since the refrigerator was in a flood and this part got submerged in water I kept it rather than returning it. I looked at everything closely and realized all the mechanical functions were working properly. Rarely does a condenser coil fail so I decided to look into recharging the coolant. Bought a 1/4 inch bullet valve, a 12oz. can of R-134a and a cheap resealable can adapter with hose, gauge and R22 to R-134a adapters. After a $30. investment Bingo, after one squirt the refrigerator began to cool and after 4oz. it now works better than new. I understand that PartSelect is in the business of selling only their parts but please consider that there can be other simple problems.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

removed door and took all the screws out of the inside door rack. removed old door seal . replaced door seal and made sure that the seal fit around and door rack fit into the groove then replaced all screws and tightened choosing random sections to tighten .replaced the door plugged back in wires that I removed and replaced door hinge screws . Shut door and checked sealing 2 hours later .Complete seal .

Parts Select included a video, and I watched a couple more that were on YouTube. Watch the video and do the repair . . . it's very easy took me about 35 min once I got the freezer emptied, including cleaning the freezer. I used a Philips head screw driver and I think it was a 5/16 nut driver . . . you can do this. Freezer running fine, no noise. One thing I would be careful on is removing the back plate that covers the fan and motor, the edges can be sharp and you could cut yourself removing the back plate. Also don't try to put the rubber gasket in before you replace the back plate, install the back plate and the rubber gasket goes in easy peasy :)

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Took longer to take out the shelves and the 10 screws holding the cover on then to replace the fan.
Local parts supply told me it would take two weeks to get the fan mator,ordered it from parts select and had in a couple days.

Cycled the defrost timer but compressor still would not kick in. Cycled the cold control, and after a while it started only to hang up again after a few hours. Replaced the cold control, now running normal.

As per instructions.removed inside shelves.removed back cover over coil let thaw.removed old thermostat &clips as per instructions.replaced with new.

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. The video that was on-line helpful also.

easy and fast

On 08/13 / 2025 starting in the AM --- My Wife Marie Defrosted -- Cleaned and dried the Kenmore up right freezer she has had for more than 33 years --- She noticed there was screws behind the inside door gasket and informed yours truly --- 1st Jacques loosened all the screws then removed the old gasket -- took it cleaned it and boxed it in the box the new gasket came in --- Took new freezer door gasket and installed it neatly around the door by tucking back part of door gasket between door panel and door --- once all was in place started tightening all screws starting at bottom holding bottom gasket material tight with other hand --- then working counter clock wise till done !!! there you go it was very easy and turned out great !!! Now everything is like new !!! Jacques And Marie / from Virginia