1068242081 Kenmore Freezer - Instructions

A You Tube video described the repair steps and by following these instructions the whole process worked seamlessly.

Emptied the inside door. Took out the screws from the top hinge. Lifted the door off the bottom hinge. Laid the door on the kitchen table. Replaced the cam on the door. Replaced the cam on the bottom hinge. Placed door back on bottom hinge and put screws back on top.

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

Googled for a solution to how to fix a refrigerator door that would not close. Was directed to a video from PartSelect. Was wrong brand, but I got the general idea. Then, I looked up a refrigerator repair for Whirlpool. Called PartSelect with my model number and ordered a Cam Kit. Total cost shipped $20. Arrived in two days during the Holidays! Nice! (Ordered 12/23, Arrived 12/26). Opened package, fired the video up. Fixed in 15 minutes. Amazing!

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Watched the video and viola, it was done. This was on the refrigerator side. Probably should have unplugged it, but didn't. One suggestion is hang a sheet in front to keep the cool in as best you can, even though it went really quickly.

I found this part on PartSelect. I was so excited it also showed a video on how to fix the door. My neighbor said he would help me and I ordered the pkg. It took 3 days to get here since I ordered Friday night and the part arrived Tuesday , this was the Easter Sunday week end also. Well the video said it was easy to do and I think it said it would take 15 min. My neighbor had it fixed in 10 min. I could not be happier. Thanks Part Select and my neighbor Mike.

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

Just loosened the screws at the top of the door hinge bracket, lifted the door off the hinge and set down on its side. Removed the broken cams, both the door cam & Cam on the lower hinge. Discarded the old parts after making sure the new parts would match up with the holes and screw holes would align. Installed a new cam on both lower hinge bracket and bottom of the door with new screws provided. Added some lubricant to minimize future wear and tear and re-installed the screws. Lifted the door back onto the lower hinge pin, Lifted up the pin on the top of door bracket until the pin would slid into the hole on top of door. Tightened the screws on top of the door hinge bracket. checked to make sure door sealed tightly around the perimeter of door opening and we were done. Total time was about 15-20 min. Anyone could do it. Thanks for the instructions and parts. Very pleased with the results. Sincerely, Jim

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Fridge side: Remove all door bins. Close the door. Pry off top hinge cap. Using 5/16" nut driver, remove three screws. Remove top hinge by lifting it up. Place pad on floor to prevent marring. Hold door at sides. Open door halfway and lift it up and off the bottom hinge. Do not let door fall! Set door on pad. The lower and upper cams are different; do not mix them up (check the parts list). Remove the old lower cam from the hinge (on fridge) and install new lower cam with new screw. Remove the old upper cam from the bottom of door and install new one with shoulder screw provided. If the old cam does not have the shim, do not use the shim from kit. The kit has extra parts and screws. Lift up the door and set it on the lower hinge pin and close it. Reinstall the upper hinge and shim loosely with the three screws. Adjust the door before tightening the screws. Check that the gasket is compressed evenly all around. Open and close the door. The door should close easily. If the door does not close easily, remove it again and smear some Vaseline on the lower hinge pin and cam. Replace the door and put a little Vaseline on the upper hinge pin before inserting it into the door. Finally, replace the upper hinge cap and replace the door bins. Repeat procedure for freezer side. This fridge does not have water/ice dispenser in the door.

Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!